PRODUCTS CENTER
Brunei TGQ series small industrial steam turbine
Category:
Product Description
TGQ series small industrial steam turbine
1. Introduction
1.1. Application
TGQ series small industrial steam turbine is generally used as prime mover and matched with boiler feed water pump of power station.
1.2. Model meaning
TGQ-**/##-&&
TGQ -- special industrial steam turbine
**---------Rating plate power (kw)
##------------Stages of steam turbine
&&----------------Modification times
1.3. Structural features
1.3.1. Structural form. There are single cylinder, double steam source, internal switch, variable speed and power, impulse condensing type.
1.3.2. Description of important characteristics
.
1.3.2.1. Impulsive design. The turbine body has compact structure, few stages, small diameter, small size, light weight, small tip and shaft seal leakage, small axial thrust, low load of thrust bearing, low oil consumption and small loss, small rotor diameter, large excessive fillet, small stress concentration factor, small thermal stress of rotor, and good adaptability to rapid load change.
1.3.2.2. the unique internal steam source switching mode (see Figure 13-1) ensures that the steam source switching process is stable and undisturbed, and the high-pressure steam source can be directly started. When the high pressure steam source is switched, the thermal shock to the turbine body is reduced to the minimum, and the stable operation of 0 ~ 100% load can be realized.
1.3.2.3. The rotor is integrally forged with high strength and low vibration sensitivity. The moving blades at all levels are non frequency regulation blades, which can adapt to a wide range of operation of the unit.
1.3.2.4. All diaphragms at all levels are of welded structure with sufficient strength and rigidity.
1.3.2.5. It can be started quickly at any time under various operation modes without turning.
1.3.2.6. The whole chassis structure of quick installation type is adopted for the steam turbine body, so the installation is fast and convenient. In half capacity configuration, two steam turbines are arranged in mirror image.
1.3.2.7. The hydraulic station adopts the containerized structure, and the main and auxiliary oil pumps, accident oil pumps, smoke exhaust fans, oil coolers and oil return filters are arranged on the oil tank.
1.3.2.8. The speed control system with meh controller as governor can realize the precise control of the whole process of turbine start and stop.
2. Main technical parameters and product appearance
2.1. Main technical parameters (see table 13-1)
Table 13-1 main technical parameters of TGQ series small industrial steam turbine
| Model | TGQ06/7-1 | TGQ10/6-1 | ||||
| Type | Single cylinder, double steam source, internal switching, variable speed and power, impulse condensing type | |||||
| Code | QG12 | QG22 | QG23 | QG32 | QG42 | QG43 |
| Low pressure steam source pressure (MPa) | 0.68~1.2 | 0.68~1.2 | ||||
| Low pressure steam source temperature(℃) | 300~400 | 300~400 | ||||
| High pressure (cold-re) steam source pressure (MPa) | 13~17.5(3.2~4.5) | 13~17.5(3.2-4.5) | ||||
| High pressure (cold-re) steam source temperature(℃) | 525~545(280~350) | 525~545(280~450) | ||||
| Exhaust pressure(kPa) | 4.7~13.1 (47.7 Air cooling) | 4.7~13.1 (47.7 Air cooling) | ||||
| Internal efficiency (%) | 80~82.5 | 80~83.1 | ||||
| Internal power(kW) | 3700~6000 | 7000~12000 | ||||
| Steam consumption rate [kg/(kW-h] | 5.0~5.6 | 4.9~5.6 | ||||
| Direction of rotation | From the head side, it is clockwise along the direction of steam flow | |||||
| Critical speed of rotor (r/min) | First stage:2550;Second stage:12 200 | First stage:2336;Second stage:7720 | ||||
| Continuous sub branch speed range (r/min) | 3000~6300 | 3000~6000 | ||||
| Steam source switching (internal switching) | About 40% rated load of main engine (constant pressure operation) | |||||
| Steam distribution mode | Low pressure steam source: nozzle steam distribution; high pressure (cold-re) generation source: throttling (nozzle) steam distribution | |||||
| Stages of steam turbine | Single row regulating stage + 6 pressure stages | Single row regulating stage + 5 pressure stages | ||||
| Nominal size of exhaust pipe(mm×mm) | ∮1620×10 | ∮2220×14 | ||||
| Rotor weight (kg) | 1850 | 2950 | ||||
| Main body weight(kg) | 29000 | 36650 | ||||
| Overall dimension (above operation floor) (mm) | 3900x3570×3080 | 4500×3700×3700 | ||||
2.2. Product appearance (see Figure 13-2)

3. Selection force method
3.1. Performance parameters
**-Q G-##-&&-(@@)
**- serial number of similar products
Q --- steam turbine
G -- industry
##--------Capacity code
&&----------Exhaust mode
(@ @ @ - --- steam source configuration)
3.1.1. Code of exhaust mode:
1 - exhaust steam upward into the main condenser;
2 - exhaust steam downward into the main condenser;
3 - exhaust steam downward into the condenser
3.1.2. Regulations on capacity Code:
1 - full capacity steam turbine matched with 200MW unit;
2-half capacity steam turbine matched with 300MW unit;
3-full capacity steam turbine matched with 300MW unit or half capacity steam turbine matched with 600MW unit;
4-semi capacity supercritical steam turbine matched with 600MW unit;
5 - semi capacity ultra supercritical steam turbine matched with 600 MW unit.
3.1.3. Steam source configuration:
L-high pressure steam source is cold regeneration steam source
D - no high pressure or cold re steam source;
Omitted - high pressure steam source is live steam.
For example, TGQ06 / 17-1QG23L indicates that the steam turbine is a 6MW steam turbine, which is used for the feed water rack of a half capacity boiler of a 30MW unit, with its own condenser, and the high-pressure steam source is the cold reheating steam source.
In addition to the typical design of boiler feed pump turbine, it can also be designed according to the user's requirements to meet the various requirements of users. The main design options are as follows:
① Single steam source design. This kind of boiler feed water pump can be simplified as the auxiliary steam source of the boiler.
② The integral chassis assembly design of the main body, which can greatly shorten the field installation period of the user, is to assemble the turbine body sleeve and the steam, water and oil pipes of the main body into a whole before leaving the factory.
③ Combined regulation system design. This design combines the regulating system of the boiler feed pump turbine with the main engine control system, cancels the governor of the boiler feed water pump turbine, and simplifies the system.
④ Control oil and lubricating oil adopt the same oil source design. In this design, the control oil, speed control oil and lubricating oil of the boiler feed pump turbine are all turbine oil, instead of fire-resistant oil as control oil and regulation oil; the control oil and control oil are separated from the main engine, which can simplify the oil system.
3.2. Supply requirements
The user can choose whether the boiler feed water pump turbine is two steam source configuration or single steam source configuration according to the requirements of the steam source provided by the main engine and the load of the main engine. The exhaust pipe and exhaust butterfly valve can be purchased by the user or provided by the boiler feed pump turbine factory.
4. Scope of supply
4.1. Scope of supply of complete equipment
4.1.1. Steam turbine body: including all parts (including pad iron, bedplate and anchor bolt) from high and low pressure main steam valve to exhaust port of low pressure cylinder.
4.1.2. Oil system: including oil tank, AC oil pump, DC oil pump, oil cooler, oil filter, smoke exhaust fan, oil level meter, electric heater, main oil pipeline and accessories above the operation layer.
4.1.3. Steam water system: including valves and throttling elements of shaft seal system and drainage system, steam and water pipes and accessories, exhaust pipes and exhaust butterfly valves above the operation layer.
4.1.4. Speed regulation and control system: including meh electro-hydraulic control system, hydraulic motor and steam distribution mechanism.
4.1.5. Protection system: including TSI monitoring and protection system, ETS emergency and trip protection system, emergency trip device, electromagnetic trip device and various monitoring, protection and interlocking instruments.
4.2. Scope of supply of random spare parts
It includes connecting bolts and nuts of cylinder and main steam valve, shaft seal, steam seal ring, spring, valve stem, valve sleeve, spring, etc.
4.3. Scope of supply of random special tools
: next page