PRODUCTS CENTER
Product Description
FK series feed water pump
1. Introduction
1.1. Application
FK series feed water pumps are mainly used in "600, 300MW steam turbine generator units" of thermal power plants, and can also be matched with gas turbine generating units.
1.2. Model meaning
FK-**-##-@@-$$-&&
FK -- FK series feed water pump code
**-------Impeller stages
##----------Hydraulic model number
@@------------Impeller outer diameter nominal size (CM)
A represents special impeller profile
No letter indicates common impeller profile
&&-------------------M for mechanical seal
No letter indicates labyrinth seal
Example: FK4E39 indicates that the series code of this type of feed water pump is FK, the number of impeller stages is 4, the hydraulic model number is E, the nominal size of impeller outer diameter is 39cm, common impeller profile, labyrinth seal.
1.3. Structural features
1.3.1. Horizontal, double shell integral core package design, integral large end cover integrated with core package.
1.3.2. High efficiency and high stability.
1.3.3. Reasonable radial clearance is based on the high efficiency, critical speed and shaft deflection standard of the pump
1.3.4. The rigid rotor ensures that the pump can operate briefly under partial vaporization.
1.3.5. The critical speed of the rotor is always more than 120% of the maximum operating speed of the pump
1.3.6. The inner hole of seal ring with shallow parallel throttling groove not only maintains the hydraulic stiffness of smooth bushing, but also increases throttling resistance, which can effectively prevent wear and bite.
1.3.7. The single balance drum structure completely eliminates the possibility of axial contact between rotor and stator.
1.3.8. The special structure at the inlet of throttle bushing of balance drum effectively reduces the damage of eddy current to the pump, greatly improves the static stiffness of liquid in the clearance, and processes the inner hole with shallow parallel groove, thus greatly reducing the leakage
1.3.9. The shaft diameter is larger, the static deflection of the rotor is small, and the rigidity is better.
1.3.10. The standard shaft torsional shear stress is conservative and does not exceed 60N / mm2
1.3.11. Wide fillet transition (radius R > 2.5mm) is adopted at the reducer of main shaft; the minimum inner fillet of keyway ensures the maximum stress concentration factor of 3.0.
1.3.12. Large size thrust bearing and cylindrical radial bearing with small ratio of length to diameter are adopted to ensure safe operation and convenient maintenance.
1.3.13. Booster stage impeller shall be adopted according to user's needs.
1.3.14. Labyrinth seal with reliable operation has no dynamic and static contact, and its design life is at least 6 years (mechanical seal can be selected by users)
1.3.15. The integral core package is convenient for maintenance. The 360 ° bearing box is directly connected with the water inlet end cover and large end cover, which reduces the assembly error and improves the anti vibration ability.
2. Main technical parameters and performance curve
FK4E39 (see Figure 2-1), FK6D32 (see Figure 2-2), FK5G32 (see Figure 2-3), FK6F32 (see Figure 2-4) and FK6G32A (see Figure 2-5).

3. Selection method
According to the design conditions of thermal power station, unit capacity and boiler operation mode. Generally, the configuration scheme of the feed water pump set is determined by the customer, and the appropriate type of feed water pump is designed and selected by the manufacturer according to the flow, head, temperature and other operating parameters provided by the customer.
The selection range of FK-1 series is shown in Table 2
Table 2-1 selection range of FK series feed water pump
| Unit load | Meet unit capacity (%) |
Model | Output flow | Head | Efficiency | Stages |
| (MW) | (m3/h) | (m) | (%) | |||
| 300 | 30 | FK6G32A | 385 | 2400 | >83 | 6 |
| 300 | 50 | FK6D32 | 600 | 2400 | >83 | 6 |
| 330 | 50 | FK5F32 | 750 | 2400 | >83 | 5 |
| 300 | 100 | FK4E39 | 1200 | 2400 | >84 | 4 |
| 600(subcritical) | 50 | FK4E39 | 1200 | 2400 | >84 | 4 |
4. Scope of supply
4.1. Feed pump body: including anchor bolt, nut, gasket, body pipe and valve, etc.
4.2. Thermal instrument: including various instruments and accessories of thermal measurement monitoring, control and protection system of pump unit.
4.3. Special tools: including hydraulic tension device, core package disassembly device, core package transportation tool, balance drum disassembly tool, thrust plate disassembly tool, etc.
4.4. Spare parts that can be provided on demand: including dynamic and static ring of mechanical seal, O-ring, wound gasket, bearing bush, thrust pad, etc.