全部
  • 全部
  • 产品管理
  • 新闻资讯
  • 介绍内容
  • 企业网点
  • 常见问题
  • 企业视频
  • 企业图册

Malta Helical gearbox for dumper driving units

Product Description

Gearbox is an independent transmission device enclosed in a rigid shell. Its function is to reduce the speed, increase the torque, and transfer the motion and power of the prime mover to the working machine. The gearbox has the advantages of compact structure, high efficiency, accurate and reliable transmission movement, convenient operation and maintenance, and can be produced in batches, so it is widely used. The commonly used gearboxes have been standardized and serialized in our country. They are produced by special manufacturers. The technical parameters can be found in relevant manuals.

 

1. Composition and classification of gearbox

1.1. The gearbox is mainly composed of transmission parts, shaft, bearing and box. Some of the transmission parts use gears, some use worm gears, and some use both. Most gearbox boxes are made of medium strength cast iron, while heavy gearbox boxes are made of high strength cast iron and cast steel. When a small number of single parts are produced, steel plates can also be welded. The shape of gearbox box is required to be simple and smooth. In order to facilitate installation, the box is often made into a split type, and the split plane is often coincident with the axis plane.

1.2. There are many types of gearboxes, and their classification methods are as follows:

1.2.1. According to the type of rotating gear, it can be divided into cylindrical gear gearbox, bevel gear gearbox, worm gearbox, planetary gear gearbox, cycloid pin gear gearbox and harmonic gear gearbox. Dumper drive unit gearbox is generally cylindrical gear gearbox

1.2.2. According to the transmission ratio series, it can be divided into single-stage gearbox and multi-stage gearbox. According to the different arrangement of gears in the box, the two-stage gearbox can be divided into expansion type, split type, coaxial type and center drive type; the gear stage of the gearbox of dumper drive unit is generally three.

1.2.3. According to the relative position of shaft in space, it can be divided into horizontal gearbox and vertical gearbox. The gearbox of dumper drive unit is generally installed horizontally

 

2. Use of gearbox

2.1. The rated value of mechanical power of gearbox is equal to or greater than the product of motor nameplate power and service factor.

2.2. The heating power of the gearbox is equal to or greater than the product of motor nameplate power and service factor

2.3. Splash lubrication, high-performance wear-resistant bearing and long-lasting oil sealing performance.

2.4. The gearbox shell adopts cast steel and steel structure.

2.5. The gear of the gearbox is helical gear or herringbone gear. It is recommended to use hard tooth surface on the surface of the gear and correct the surface properly so as to get good meshing. Hard tooth surface has good mechanical properties, high strength and long service life. Compared with ordinary gear gearbox, hard gear gearbox with the same strength and service life can greatly reduce its volume and prolong its service life.

2.6. An oil level observation scale, removable inspection cover and air vent are set on the gearbox shell. There is a cover on the end of the shaft that is not used. It should be noted that: when the gearbox system is subject to abnormal impact, it is prone to tooth surface pitting, broken teeth, bearing damage and other problems. If the vibration of the drive system exceeds the standard for a long time, it is easy to cause resonance and damage to the whole gearbox. Therefore, great attention must be paid to the installation of the driving device, and the accuracy requirements of the motor and mechanical coupling matched with the gearbox must be met. The framework oil seal at the high speed shaft end of the gearbox is easy to be damaged and leaked, so it needs to be replaced timely.

The gearbox commonly used in dumper drive unit include Flender's H series gearboxes, China's Z series gearboxes, and polyhedron mounted parallel shaft involute cylindrical gears of some factories. These gearboxes are generally three-stage gears with a speed ratio of about 40:1.