全部
  • 全部
  • 产品管理
  • 新闻资讯
  • 介绍内容
  • 企业网点
  • 常见问题
  • 企业视频
  • 企业图册

Product Description

YOCQ-X51 fluid coupling

 

1. Introduction

1.1. Application

YOCQ-X51 fluid coupling is mainly used for speed regulating operation of boiler feed water pump set of 300MW (50%) and 600MW (30%) units.

1.2. Model meaning

YOCQ-X51

YOC -- hydraulic coupling transmission device

Q -------- front end

X51 -------- effective diameter nominal size of pump wheel (cm)

1.3. Structural features

1.3.1. Structure description. The working principle of YOCQ-X51 fluid coupling (see Fig. 12-1) is that the main motor drives the speed increasing gear pair to rotate the pump wheel. Driven by the impeller blades, the working oil flows from the inner side (inlet) of the pump wheel to the outer edge (outlet) due to the centrifugal force, forming high-pressure and high-speed liquid flow, which impulses the driven turbine blade and makes the driven turbine rotate in the same direction with the pump wheel; The working oil flows from the outer edge (inlet) to the inner (outlet) of the driven turbine by reducing pressure and decelerating, and then flows into the inlet of the pump wheel to form a circular circle. In the process of circulating flow, the pump wheel converts the input mechanical work into the kinetic energy of working oil and the potential energy of increasing pressure, while the driven turbine converts the kinetic energy and potential energy of working oil into the output mechanical work to drive the boiler The water pump supplies water to the boiler, so as to realize the power transfer between the motor and the feed water pump

The oil circulation in the hydraulic coupling is maintained by the pressure difference formed by the centrifugal force between the pump wheel and the turbine passage. In order to ensure the oil circulation, the pump wheel and turbine must rotate at different speeds, that is, there is a slip, which is 2% ~ 3% of the input speed under rated operating conditions. By adjusting the working position of the scoop tube, the filling degree of the circulating oil in the flow passage of the hydraulic coupler can be changed, so as to change the slip, realize the stepless speed regulation of the driven mechanical feed pump, and make the feed water pump run according to the load characteristic curve.

The power loss of the hydraulic coupler changes into heat, which makes the working oil temperature rise; the working oil enters the oil cooler through the scoop tube for cooling. When the oil temperature in the working chamber exceeds 160 ℃, the fusible plug on the working chamber melts and the working oil is discharged.

1.3.1.1. Oil system. The oil system is divided into working oil circuit and lubricating oil circuit. The oil supply of working oil and lubricating oil is the same. The main oil pump (gear pump) is driven by the oil pump drive gear on the input shaft, which supplies oil to the working oil circuit and lubricating oil circuit at the same time.

Before the whole pump set is started or the moment when the main motor is shut down, and when the system is disturbed, the motor of the auxiliary oil pump drives the auxiliary oil pump to supply oil.

The working oil circuit (see Fig. 12-1) consists of an open circuit and a closed circuit to adjust the oil charge. The oil supplied by the main oil pump is fed into the working chamber of the coupler through the flow regulating valve after passing through the lubricating oil pressure reducing valve. This is an open circuit: under the action of pressure, the working oil in the working chamber of the hydraulic coupler is returned to the working chamber of the coupler through the working oil cooler, and then returned to the working chamber of the coupler through the working oil pressure reducing valve and flow regulating valve It is a closed circuit. The surplus oil supplied by the main oil pump flows through the working oil pressure reducing valve and returns to the oil tank.

The outlet oil pressure of the main oil pump, the inlet oil pressure of the working oil flow regulating valve and the return oil pressure of the scoop pipe are respectively displayed on three pressure gauges connected to the outside of the tank

The main oil pump (12-12) enters into the main oil tank and the oil pressure of the oil suction check valve (see Fig.

The lubricating oil pressure set by the lubricating oil constant pressure valve on the hydraulic coupler is about 2.0kg/cm2 (0.2MPa). In order to ensure that each bearing part has oil film during the start and stop of hydraulic coupler, auxiliary lubricating oil pump is used to supply lubricating oil for the unit before and after the main motor starts and stops. The auxiliary oil pump is driven by a small motor, and the oil inhaled from the oil tank enters the lubricating oil system through the one-way check valve of the auxiliary oil pump.

1.3.1.2. External oil supply system (see Figure 12-1). For the external lubricating oil of the hydraulic coupling (such as the main motor and feed pump driving the hydraulic coupling, as well as connecting the coupling wheel, etc.), the lubricating oil can be distributed from the lubricating oil system circuit of the hydraulic coupling, and the lubricating oil flows through the oil return pipe and returns to the oil tank. The external lubricating oil quantity of the unit shall not exceed the quantity specified in the technical parameters.

The orifice plates for controlling the external oil supply are respectively installed on the output pipe of the lubricating oil main pipe of the hydraulic coupler. One end of the orifice is connected to the motor and the other end is to the feed pump. The orifice size of the orifice plate (see Figure 12-2) is designed according to the needs of the external oil quantity. Before operation, the aperture of these flow orifices can be adjusted according to the actual needs of the system.

1.3.2. Description of important components. The axial force of the gear can cancel each other when the gear transmits torque by using the first grade herringbone gear pair. The structure of once grinding hard tooth surface ensures the high machining accuracy and reliability of gear. The gear material is made of high-quality alloy steel. The gear surface is carburized, Quenched and ground. The precision and strength meet the national standard. The gear shaft is connected by oil pressure cone surface interference, which is convenient for assembly and disassembly. This structure has large torque transmission and is especially suitable for gears to bear alternating loads. All rotating parts are tested for balance, and the dynamic balance accuracy meets the requirements of ISO 1940.

 

2. Main technical parameters and product appearance

2.1. Main technical parameters (see table 12-1)

Table 12-1 main parameters of YOCQ-X51 fluid coupling

Items Parameters
Fluid coupling
Input speed(r/min) 1493
Slip(%) ≤3
Variable speed range(%) 25~100
Oil tank volume (L) 1300
Weight (without oil)(kg) 6000
Rotating speed (view from the input side) Input shaft: CCW;output shaft:CW
Oil cooler
Model LYQ-01(Working oil cooler) LYQ-02(Lubrication oil cooler)
Cooling areas(m2) 65 30
Cooling water volume (L/min) 1500 325
Inlet water temperature (℃) ≤33 ≤33
Weight (without oil and water)(kg) 1314 738
Auxiliary pump motor
Model Y132M-4
Power(kW) 7.5
Speed(r/min) 1440

2.2. Product appearance (see Figure 12-3)

 

3. Scope of supply

3.1. Hydraulic coupler body: including anchor bolt and pad iron, internal oil pipeline and valve, oil filter, electric actuator, etc.

3.2. Working oil cooler.

3.3. Lubricating oil cooler.

3.4. Body gauge: including pressure, temperature, bearing bush temperature, etc.