PRODUCTS CENTER
Product Description
FU chain conveyor
1. Introduction
1.1. Purpose
FU chain conveyor is a new mechanical product which is used to transport powdery and granular materials horizontally (or the inclination angle is less than or equal to 15), which is imported from foreign advanced technology, and is widely used in building materials, construction, chemical industry, mining, machinery and metallurgy Refining, grain feed processing and other industries, is an ideal new type of conveying equipment.
1.2. Structural features
1.2.1. Reasonable structure, novel design, advanced technology and complete series.
1.2.2. FUlly enclosed casing, good sealing performance, safe operation and reliable operation.
1.2.3. The conveyor chain is made of alloy steel by advanced heat treatment, with long service life and low maintenance rate.
1.2.4. The conveying capacity can reach 11m3 / h
1.2.5. The energy consumption of conveying is low. With the help of the internal friction force of materials, the material is transformed into tension force, which saves electricity and is durable.
1.2.6. The inlet and outlet are flexible. The elevated, ground, pit, horizontal and climbing (inclination angle less than or equal to 15 °) can be installed, and the conveying length can be designed by the user.
2. Main technical parameters
2.1. Technical parameters
The main technical parameters of FU chain conveyor and its optimum conveying capacity at different chain speeds are shown in table 39-1 and table 39-2 respectively. The optimum conveying capacity is calculated with cement as the material. It can be used in other industries to transport materials with low grindability and temperature lower than 60 ℃. Material humidity is less than or equal to 5%, refers to the hands wet into a ball, hands can disperse.
Table 39-1 main technical parameters of FU chain conveyor
| Model | Groove width (mm) | Ideal particle size (mm) | 10% Maximum particle size (mm) | Maximum conveying angle (°) | Material humidity (%) |
| FU150 | 150 | <4 | <8 | ≤15 | ≤5 |
| FU200 | 200 | <5 | <10 | ||
| FU270 | 270 | <7 | <15 | ||
| FU350 | 350 | <9 | <18 | ||
| FU410 | 410 | <11 | <21 | ||
| FU500 | 500 | <13 | <25 | ||
| FU600 | 600 | <15 | <30 |
Table 39-2 optimum conveying capacity of FU chain conveyor at different chain speeds
| Model | Chain speed(m/min) | ||||||
| 10 | 12 | 13.5 | 15 | 16 | 20 | 25 | |
| Most suitable conveying volume(m3/h) | |||||||
| FU150 | 6~9 | — | — | 9~13 | — | 12~18 | 15~23 |
| FU200 | 11~14 | — | — | 16~22 | — | 22~29 | 27~36 |
| FU270 | 19~14 | 23~32 | 25~36 | 28~41 | 31~43 | 38~54 | 47~68 |
| FU350 | 19~27 | 36~50 | — | 49~68 | — | 65~90 | 63~113 |
| FU410 | — | 50~72 | — | 63~90 | — | 86~117 | 95~135 |
| FU500 | — | 72~99 | — | 95~131 | — | 136~180 | 144~203 |
| FU600 | — | 104~144 | — | 135~190 | — | 180~260 | 207~270 |
2.2. Transport link
The recommended chain speeds for conveying materials with different grindability are shown in table 39-3
Table 39-3 recommended chain speeds for conveying different abrasive materials
| Material grindability | Extra high | High | Middle | Small | |
| Chain speed(m/min) | Suggest | 10 | 15 | 20 | 30 |
| Max. | 15 | 20 | 30 | 40 | |
3. Selection method
3.1. Equipment selection
3.1.1. Chain speed. The chain speed is selected according to the state of the material, and the slow speed is selected for the materials with strong grindability, high temperature, large proportion of coarse particles and large particles. See table 39-4 for the most suitable chain speed for transporting mature raw materials and finished powder materials of cement. Other materials with similar properties and state of cement can be selected by reference.
Table 39-4 the most suitable chain speed for conveying raw and cooked raw materials and finished powder of cement
| Material | Raw fine powder or cement product | Clinker fines or cement products | Raw meal or clinker coarse powder return | |
| Material temperature(℃) | <60 | 60~120 | <60 | 60~120 |
| Most suitable chain speed (m/min) | 15~20 | 10~13.5 | 10~20 | 10 |
| Max. chain speed (m/min) | 25 | 15 | 13.5 | 12 |
3.1.2. Model. Select the model according to the conveying capacity. Under the same conveying capacity, the chain speed can be reduced and the service life can be prolonged by selecting a larger type. However, when the conveying capacity is less than 30% of the conveying capacity, the material layer will be too thin, resulting in idling and increasing wear.
3.1.3. Power. According to the conveying capacity, conveying length and process conditions, the power is selected according to table 39-5 ~ table 39-9. When the values in brackets are selected, the acceptance conditions shall be discussed separately. The assembly form of driving device is divided into back mounting and left and right mounting.
3.1.4. Import and export. The user can select the inlet and outlet as required
3.1.4.1. For materials with poor fluidity and high humidity, it is not suitable to use the upper inlet.
3.1.4.2. When the first feed port is close to the tail shaft, the upper feed port should not be used.
3.1.4.3. According to the user's needs, the machine can be equipped with multiple inlet and outlet, and can also be provided with gate outlet.
Table 39-5 selection of driving device and maximum conveying length of FU150 chain conveyor
| Material charactors | Rated capacity (m3/h) | Conveyor chain speed (m/min) | Spindle speed (r/min) | Driving system | Maximum distance of corresponding power transmission (m) | ||||||
| Normal temperature, low Grindability | High temperature, high Grindability | Cycloid geared motor | Material weight (t/m3) | ||||||||
| Model | 0.5 | 0.8 | 1 | 1.2 | 1.5 | 1.8 | |||||
| Select | Select | 10 | 11 | 12 | XWD2.2-5-71 | 50 | 41 | 36.5 | 32.5 | 28.5 | 25 |
| XWD3-5-71 | (68.5) | (56) | 49.5 | 44.5 | 39 | 34.5 | |||||
| 26 | 17 | 18 | XWD2.2-5-47 | 32 | 26.5 | 23.5 | 21 | 18.5 | 16 | ||
| XWD3-5-47 | 44 | 36 | 32 | 29 | 25 | 22 | |||||
| XWD4-6-47 | -59 | 48 | 43 | 38.5 | 33.5 | 29.5 | |||||
| XWD5.5-7-47 | (81.5) | (66) | (59) | (53) | 46 | 41 | |||||
| Select under control | 20 | 22 | 24 | XWD1.1-4-35 | 12.5 | 10 | 9 | 8 | 7 | 6 | |
| XWD1.5-4-35 | 17 | 14 | 12 | 11 | 9.5 | 8.5 | |||||
| XWD2.2-5-35 | 25 | 20.5 | 18 | 16 | 14 | 12.5 | |||||
| XWD3-5-35 | 34 | 28 | 24.5 | 22 | 19.5 | 17 | |||||
| XWD4-5-35 | 45.5 | 37 | 33 | 30 | 26 | 23 | |||||
| XWD5.5-6-35 | (63) | (51) | 45.5 | 41 | 35.5 | 31.5 | |||||
| XWD7.5-6-35 | (85.5) | (70) | (62) | (56) | 48.5 | 43 | |||||
Table 39-6 selection of driving device and maximum conveying length of FU200 chain conveyor
| Material charactors | Rated capacity (m3/h) | Conveyor chain speed (m/min) | Spindle speed (r/min) | Driving system | Chain row | Maximum distance of corresponding power transmission (m) | ||||||
| Normal temperature, low Grindability | High temperature, high Grindability | Cycloid geared motor | Material weight (t/m3) | |||||||||
| Model | 0.5 | 0.8 | 1 | 1.2 | 1.5 | 1.8 | ||||||
| Select | Select | 18 | 11 | 9 | XDW2.2-5-71 | Single | 31 | 25.5 | 22.5 | 20.5 | 18 | 16 |
| XDW3-5-71 | Single | 42.5 | 35 | 31 | 27.5 | 25 | 21.5 | |||||
| XDW4-6-47 | Double | 56.5 | 46 | 41 | 37 | 32.5 | 29 | |||||
| XDW5.5-7-47 | Double | (71.5) | (63.5) | 56.5 | 51 | 41.5 | 29.5 | |||||
| 28 | 17 | 14 | XDW2.2-5-47 | Single | 20 | 16.5 | 14 | 13 | 11 | 0 | ||
| XDW3-5-47 | Single | 27 | 22 | 19.5 | 17.5 | 15.5 | 13.5 | |||||
| XDW4-6-47 | Single | 36 | 29 | 26 | 23.5 | 20.5 | 18 | |||||
| XDW5.5-6-47 | Double | 50 | 40.5 | 36 | 32.5 | 28 | 25 | |||||
| XDW7.5-7-47 | Double | -67.5 | 55 | 49 | 41.5 | 38.5 | 34.5 | |||||
| Select under control | 38 | 22 | 18 | XDW2.2-5-35 | Single | 14.5 | 12 | 11 | 9.5 | 8.5 | 7.5 | |
| XDW3-5-35 | Single | 20 | 16.5 | 14.5 | 13 | 11 | 10 | |||||
| XDW4-5-35 | Single | 26.5 | 21.5 | 19 | 17.5 | 15 | 13.5 | |||||
| XDW5.5-6-35 | Single | 37 | 30 | 27 | 24 | 21 | 18.5 | |||||
| XDW15-6-35 | Double | 50 | 41 | 36.5 | 32 | 28.35 | 25 | |||||
| XDW11-7-35 | Double | (73.5) | (60) | 53.5 | 48 | 42 | 37 | |||||
Table 39-7 selection of maximum conveying length of driving device of FU270 chain conveyor
| Material charactors | Rated capacity (m3/h) | Conveyor chain speed (m/min) | Spindle speed (r/min) | Driving system | Chain drive | Maximum distance of corresponding power transmission (m) | ||||||
| Normal temperature, low Grindability | High temperature, high Grindability | Cycloid geared motor | Pitch (mm) | Material weight (t/m3) | ||||||||
| Model | 0.5 | 0.8 | 1 | 1.2 | 1.5 | 1.8 | ||||||
| Select | Select | 33 | 11 | 6.5 | XWD4-6-71 | 31.75 | 34 | 29 | 25 | 22 | 18 | 16 |
| XWD6.5-7-71 | 31.75 | 47 | 40 | 31 | 30 | 25 | 22 | |||||
| XWD7.2-8-71 | 31.75 | 64 | 54 | 17 | 41 | 35 | 30 | |||||
| XWD11-9-71 | 38.1 | (90) | (75) | (65) | 56 | 45 | 40 | |||||
| 40 | 13.5 | 8 | XWD4-6-59 | 31.75 | 27 | 22 | 19 | 17 | 14 | 12 | ||
| XWD5.5-7-59 | 31.75 | 37 | 31 | 27 | 24 | 20 | 17 | |||||
| XWD7.5-8-59 | 31.75 | 51 | 43 | 37 | 32 | 27 | 24 | |||||
| XWD11-8-59 | 38.1 | 74 | 63 | 54 | 48 | 40 | 35 | |||||
| XWD15-9-59 | 38.1 | (90) | (75) | (65) | 56 | 45 | 40 | |||||
| 50 | 17 | 10 | XWD6.5-6.47 | 31.75 | 30 | 25 | 22 | 19 | 16 | 14 | ||
| XWD7.5-7-47 | 31.75 | 42 | 35 | 30 | 26 | 22 | 19 | |||||
| XWD11-8-47 | 38.1 | 61 | 51 | 41 | 39 | 33 | 29 | |||||
| XWD18.5-8-29 | 38.1 | (90) | (75) | (65) | 56 | 45 | 40 | |||||
| Select under control | 68 | 22 | 13 | XWD5.5-6.35 | 31.75 | 22 | 19 | 16 | 14 | 12 | 10 | |
| XWD7.5-6-35 | 31.75 | 30 | 26 | 22 | 19 | 16 | 14 | |||||
| XWD11-7-35 | 38.1 | 45 | 38 | 33 | 29 | 24 | 21 | |||||
| XWD15-8-35 | 38.1 | (62 | 52 | 45 | 39 | 33 | 29 | |||||
| XWD18.5-8-23 | 38.1 | (76) | (61) | 55 | 49 | 41 | 36 | |||||
| Cannot be selected | 82 | 27 | 16 | XWD7.5-6-9 | 31.75 | 21 | 20 | 17 | 15 | 13 | 11 | |
| XWD11-7-29 | 38.1 | 36 | 30 | 26 | 23 | 19 | 17 | |||||
| XWD15-8-29 | 38.1 | 49 | 41 | 36 | 31 | 26 | 23 | |||||
| XWD18.5-8-17 | 38.1 | 60 | 51 | 44 | 39 | 33 | 28 | |||||
| XWD22-9-17 | 38.1 | (72) | (60) | 52 | 46 | 39 | 34 | |||||
Table 39-8 selection of driving device and maximum conveying length of FU350 chain conveyor
| Material charactors | Rated capacity (m3/h) | Conveyor chain speed (m/min) | Spindle speed (r/min) | Driving system | Chain drive | Maximum distance of corresponding power transmission (m) | ||||||
| Normal temperature, low Grindability | High temperature, high Grindability | Cycloid geared motor | Pitch (mm) | Material weight (t/m3) | ||||||||
| Model | 0.5 | 0.8 | 1 | 1.2 | 1.5 | 1.8 | ||||||
| Select | Select | 64 | 14 | 6.3 | XWD1-6-71 | 38.1 | 21.5 | 16.5 | 11 | 12.5 | 10.5 | 9 |
| XWD5.5-7-71 | 29.5 | 22.5 | 19.5 | 17 | 14.5 | 12.5 | ||||||
| XWD7.5-8-71 | 40.5 | 31 | 27 | 23.5 | 20 | 17.5 | ||||||
| XWD11-9-71 | (60) | 45.5 | 39.5 | 34.5 | 29.5 | 25.5 | ||||||
| XWD15-9-71 | 44.45 | (81.5) | (62.5) | 54 | 47.5 | 40 | 35 | |||||
| 80 | 17 | 7.5 | XWD4-6-59 | 38.1 | 17.5 | 13 | 11.5 | 10 | 8.5 | 7.5 | ||
| XWD5.5-7-59 | 24 | 18.5 | 16 | 14 | 11.5 | 10 | ||||||
| XWD7.5-8-59 | 33 | 25 | 21.5 | 19 | 16 | 14 | ||||||
| XWD11-8-59 | 48.5 | 37 | 32 | 28 | 23.5 | 20.5 | ||||||
| XWD15-9-59 | 44.45 | (66 | 50.5 | 43.5 | 38 | 32.5 | 28 | |||||
| XWD18.5-9-43 | (81.5) | (62) | 53.5 | 47 | 40 | 31.5 | ||||||
| Select under control | 98 | 21 | 9.5 | XWD5.5-6-47 | 38.1 | 19.5 | 15 | 13 | 11.5 | 95 | 8 | |
| XWD7.5-7-47 | 26.5 | 20.5 | 17.5 | 15.5 | 13 | 11.5 | ||||||
| XWD11-8-47 | 39.5 | 30 | 26 | 22.5 | 19 | 16.5 | ||||||
| XWD18.5-8-29 | 44.45 | (66 | 50.5 | 43.5 | 38.5 | 32.5 | 28 | |||||
| XWD22-9-29 | (79) | (60) | 52 | 45.5 | 38.5 | 33.5 | ||||||
| Cannot be selected | 130 | 28 | 12.7 | XWD7.5-6-35 | 38.1 | 20 | 15 | 13 | 11.5 | 10 | 8.5 | |
| XWD11-7-35 | 29.5 | 22.5 | 19.5 | 17 | 14.5 | 12.5 | ||||||
| XWD15-8-35 | 44.45 | 40.5 | 30.5 | 26.5 | 23.5 | 20 | 17 | |||||
| XWD18.5-8-23 | 19.5 | 33 | 33 | 29 | 24.5 | 21 | ||||||
| XWD22-10-23 | 59 | 45 | 39 | 34.5 | 29 | 25 | ||||||
| XWD30-10-23 | (81) | (61.5) | 53.5 | 47 | 40 | 34.5 | ||||||
Table 39-9 selection of driving device and maximum conveying length of FU410 chain conveyor
| Material charactors | Rated capacity (m3/h) | Conveyor chain speed (m/min) | Spindle speed (r/min) | Driving system | Maximum distance of corresponding power transmission (m) | Conveyor chain type | ||||||
| Normal temperature, low Grindability | High temperature, high Grindability | Cycloid geared motor | Material weight (t/m3) | |||||||||
| Model | 0.5 | 0.8 | 1 | 1.2 | 1.5 | 1.8 | ||||||
| Select | Select | 64 | 14 | 6.3 | XWD4-6-71 | 16.5 | 12.5 | 10.5 | 9 | 7.5 | 6.5 | Ordinary |
| XWD5.5-7-71 | 23 | 17 | 14.5 | 12.5 | 10.5 | 9 | ||||||
| XWD7.5-8-71 | 31.5 | 23.5 | 20 | 17.5 | 14.5 | 12.5 | ||||||
| XWD11-9-71 | 46.5 | 34.5 | 29.5 | 25.5 | 21.5 | 18.5 | ||||||
| XWD15-9-71 | (63) | 47 | 40 | 35 | 29.5 | 25.5 | ||||||
| XWD22-10-47 | (83) | (64) | 55.5 | 45 | 40 | 35 | Enhanced | |||||
| 80 | 17 | 7.5 | XWD4-6-59 | 13.5 | 10 | 8.5 | 7.5 | 6.5 | 5.5 | Ordinary | ||
| XWD5.5-7-59 | 19 | 14 | 12 | 10.5 | 9.5 | 7.5 | ||||||
| XWD7.5-8-59 | 26 | 19 | 16.5 | 14.5 | 12 | 10.5 | ||||||
| XWD11-8-59 | 38 | 28.5 | 24 | 21 | 17.5 | 15 | ||||||
| XWD15-9-59 | 52 | 38.5 | 33 | 29 | 24 | 21 | ||||||
| XWD18.5-9-43 | (64) | 47.5 | 41 | 35.5 | 30 | 25.5 | ||||||
| XWD22-10-43 | (69) | 53 | 45.5 | 40 | 34.5 | 29.5 | Enhanced | |||||
| Select under control | 98 | 21 | 9.5 | XWD5.5-6-47 | 15 | 11.5 | 9.5 | 8.5 | 7 | 6 | Ordinary | |
| XWD7.5-7-47 | 21 | 15.5 | 13 | 11.5 | 9.5 | 8.5 | ||||||
| XWD11-8-47 | 30.5 | 23 | 19.5 | 17 | 14.5 | 12.5 | ||||||
| XWD18.5-8-29 | 52 | 38.5 | 33 | 29 | 24 | 21 | ||||||
| XWD22-10-29 | (61.5) | 46 | 39.5 | 34.5 | 29 | 25 | ||||||
| XWD30-10-29 | (83) | 58.5 | 50.5 | 44.5 | 37.5 | 32.5 | Enhanced | |||||
| Cannot be selected | 130 | 28 | 12.7 | XWD7.5-6-35 | 15.5 | 11.5 | 10 | 8.5 | 7 | 6 | Ordinary | |
| XWD11-7-35 | 23 | 17 | 14.5 | 12.5 | 10.5 | 9 | ||||||
| XWD15-8-35 | 31.5 | 23.5 | 20 | 17.5 | 14.5 | 12.5 | ||||||
| XWD18.5-8-23 | 39 | 29 | 24.5 | 21.5 | 18 | 15.5 | ||||||
| XWD22-10-23 | 46 | 34.5 | 29.5 | 25.5 | 21.5 | 18.5 | ||||||
| XWD30-10-23 | (63) | 47 | 40 | 35 | 29.5 | 25.5 | ||||||
| XWD37-11-23 | (83) | 54 | 46.5 | 41 | 34.5 | 30 | Enhanced | |||||
Note: in table 39-5 to table 39-9, the material capacity (T / m3) is 0.5, 0.8, 1.0, 1.2, 1.5 and 1.8 respectively
3.1.4.4. The discount coefficient of inclined conveying is shown in table 39-10
Table 39-10 discount coefficient for inclined conveying
| Incline(°) | 0~2.5 | 2.5~5 | 5~7.5 | 7.5~10 | 10~12.5 | 12.5~15 |
| Capacity discount | 1 | 0.95 | 0.9 | 0.85 | 0.8 | 0.7 |
3.2. Conveying mode
The conveying form of FU chain conveyor is shown in figure 39-1

4. Equipment appearance
The structure and driving device of FU chain conveyor are shown in Fig. 39-2
