PRODUCTS CENTER
Malta Resin separation tower (SPT)
Category:
Product Description
Resin separation tower (SPT)
1. Introduction
1.1 purpose
Resin separation column is used in condensate polishing in vitro regeneration system, which is the most important equipment of "finesep" high column separation technology. The anion and cation resins that failed in the condensate polishing mixed bed are transported to the resin separation tower, and the anion and cation resins are completely separated by air scrubbing and hydraulic screening.
1.2 model significance
1.2.1. The water inlet device is in the form of mother branch pipe, and the branch pipe is covered with trapezoidal wire winding.
1.2.2. The water outlet device is a porous plate with a double speed water cap.
1.2.3. The equipment is lined with 1751 semi-rigid rubber.
1.2.4. The equipment is an inverted conical structure with smaller diameter at the lower part.
1.4 product series
The product series of resin separation tower is shown in table 56-1
Table 56-1 product series of resin separation tower
| Nominal meter (mm) Model Item |
DN1300/DN2100 | DN1600/DN2600 | DN1800/DN2600 |
| JF130/210·3.8 | JF160/260·9.2 | JF180/260·10.8 | |
| Resin volume(m3) | 3.8 | 9.2 | 10.8 |
| Design weight(kg) | 3350 | 6010 | 6800 |
| Running load(N) | 13500 | 30000 | 33000 |
| Typical application(MW) | 300WM | 600、1000MW | 1000MW、CPR1000 |
2. Technical parameters
The main technical parameters of resin separation tower are shown in table 56-2
Table 56-2 main technical parameters of resin separation tower
| Item | Data | Item | Data |
| Design pressure(MPa) | 0.6 | Backwash expansion rate | >100% |
| Design temperature(℃) | 50 | Welded joint coefficient | 0.85 |
| material of the main body | Q235-B | container form | Vertical |
3. Equipment appearance and structural dimensions
The external structure of resin separation tower is shown in Fig. 56-1, table 56-3 and table 56-4

Table 56-3
| Nominal diameter Item |
DN1/DN2 | ||
| DN1300/DN2100 | DN1600/DN2600 | DN1800/DN2600 | |
| H | 7630 | 10200 | 10720 |
| H1 | 1045 | 1325 | 1247 |
| H2 | 5900 | 8060 | 8670 |
| H3 | 2274 | 2930 | 2232 |
| H4 | 3858 | 5180 | 5214 |
| H5 | 5600 | 7760 | 8364 |
| H6 | 590 | 743 | 640 |
| L | 1160 | 1485 | 1400 |
| L1 | 305 | 305 | 366 |
| ∮ | 810 | 1620 | 1820 |
Table 56-4 nozzle of resin separation tower
| Nozzle Code | Usage | Nominal dimensions | ||
| DN1300/DN2100 | DN1600/DN2600 | DN1800/DN2600 | ||
| N1 | Exhause port | 450 | 450 | 450 |
| N2 | water inlet | 100 | 150 | 150 |
| N3 | Resin outlet | 80 | 80 | 80 |
| N4 | water outlet | 80 | 80 | 80 |
| N5 | Resign inlet | 450 | 500 | 500 |
| N6 | Regeneration fluid inlet | 80 | 150 | 150 |
| N7~N10 | Mirror | 80 | 80 | 80 |
| N11 | Top hole | 140×40 | 140×40 | 140×40 |
| N12 | side hole | 40 | 50 | 50 |