PRODUCTS CENTER
Malta Anion resin regeneration tower (ART)
Category:
Product Description
Anion resin regeneration tower (ART)
1. Introduction
1.1. Purpose
Anion resin regeneration tower is used for condensate polishing in vitro regeneration system. The anion resin separated from the resin separation tower is sent to the equipment for cleaning and thorough regeneration.
1.2. Model meaning
JZY•160
J --- ion exchange
Z -- Regeneration
Y -- anion resin
160 -- equipment diameter (mm)
1.3. Structural features
1.3.1. The water inlet device is arc-shaped water baffle.
1.3.2. The alkali inlet device is in the form of main branch pipe, and the branch pipe is covered with trapezoidal wire winding.
1.3.3. The water outlet device is a porous plate with a double speed water cap.
1.3.4. The equipment is lined with 1751 semi-rigid rubber.
1.4. Product series
See table 53-1 for the product series of anion resin regeneration tower.
Table 53-1 anion resin regeneration tower product series
| Nominal meter (mm) Model Item |
DN1200 | DN1600 | DN2000 |
| JZY120 | JZY160 | JZY200 | |
| Resin volume(m3) | 1. 90 | 4.6 | 7.2 |
| Design weight(kg) | 1800 | 2390 | 4500 |
| Running load(N) | 15 000 | 20000 | 32000 |
| Typical application(MW) | 300 | 600、1000 | 1000、CPR1000 |
2. Technical parameters
The main technical parameters of anion resin regeneration tower are shown in table 53-2.
Table 53-2 main technical parameters of anion resin regeneration tower
| Item | Data | Item | Data |
| Design pressure(MPa) | 0.6 | Backwash expansion rate | 100% |
| Design temperature(℃) | 50 | Welded joint coefficient | 0.85 |
| material of the main body | Q235-B | container form | Vertical |
3. Equipment appearance and structural dimensions
The external structure of anion resin regeneration tower is shown in Fig. 53-1, table 53-3 and table 53-4

Table 53-3 external dimensions of anion resin regeneration tower (mm)
| Nominal diameter Item |
DN1200 | DN1600 | DN2000 |
| H | 5070 | 5900 | 6470 |
| H1 | 1025 | 1340 | 1295 |
| H2 | 3580 | 4015 | 4540 |
| H3 | 1870 | 2600 | 2880 |
| H4 | 1770 | 2300 | 2780 |
| H5 | 590 | 743 | 640 |
| L | 765 | 960 | 1150 |
| L1 | 230 | 305 | 366 |
| ∮ | 790 | 1050 | 1310 |
Table 53-4 orifice table of anion resin regeneration tower (mm)
| Nozzle Code | Usage | Nominal dimensions | ||
| DN1200 | DN1800 | DN2000 | ||
| N1 | Exhause port | 40 | 50 | 50 |
| N2 | water inlet | 80 | 80 | 80 |
| N3 | Resin outlet | 80 | 80 | 80 |
| N4 | water outlet | 80 | 80 | 80 |
| N5 | Resign inlet | 80 | 80 | 80 |
| N6 | Regeneration fluid inlet | 50 | 65 | 65 |
| N7~N10 | Mirror | 140×40 | 140×40 | 140×40 |
| N11 | Top hole | 450 | 450 | 450 |
| N12 | side hole | 500 | 500 | 500 |