PRODUCTS CENTER
Product Description
PG series coal feeder
1. Introduction
1.1. Purpose
DPG series coal feeder is a weighing coal feeder specially developed by bjepc for coal-fired units in power system. This series of coal feeders can feed coal quantitatively and accurately. It is suitable for the positive pressure or negative pressure operation conditions of the pulverizing system. It is also suitable for the coal pulverizing system of metallurgy, chemical industry, building materials and other industries.
1.2. Model meaning
DPG ***
DPG -- Product Model Code
***----Product specification code
The product specification code is expressed by the hourly feed rate (unit t/h) of the coal feeder; the product model code is represented by the abbreviation of Chinese Pinyin symbol DPG for the electronic belt scale coal feeder. For example, DGP40 is an electronic belt scale coal feeder with coal feeding capacity of 40t/h.
1.3. Basic structure and characteristics
1.3.1. The basic structure of DPG series coal feeder is shown in figure 18-1.

DPG series coal feeder consists of belt conveyor, metering device, chain cleaning device, fully enclosed shell and control cabinet. The inlet and outlet of coal feeder must be equipped with coal gate, that is, according to the operation conditions and structural characteristics of the system, electric, hydraulic or pneumatic coal gate shall be equipped.
1.3.2. Structural features of DPG series coal feeder:
1.3.2.1. Load cell with dust explosion-proof structure. The bellows type load cell with Siemens unique technology is suitable for the dangerous environment full of combustible dust. Complete metal seal, protection grade up to IP66, ultra-high precision measurement in small capacity.
1.3.2.2. Adjust the simple BW500 calculus regulator. It processes the load and speed signals of the belt, and measures the accurate flow rate and cumulative mass of solid bulk materials. Control dominates data communication and Fieldbus connection, and patented strain sensor balancing eliminates strain sensor matching.
1.3.2.3. The control system adopts modular structure. The division of work of measurement and regulation, PLC program control, frequency control and other functional blocks is clear and clear. Milltronics dolphin plus software can program the device on PC. the selected components are commonly used by domestic users, which is easy for users and technicians to use and maintain.
1.3.2.4. Cylindrical pressure resisting structure. The cross section of coal inlet is designed to be circular, and coal can fall into the belt continuously and evenly, so the best measurement accuracy can be obtained. In addition, it can be sealed with external pressure without air leakage.
1.3.2.5. Special belt and cleaning chain. The special belt adopts a 60mm high skirt ring-shaped jointless design. Compared with the slit rib, the belt will not produce gap when passing through the driving roller, so the coal falling can be reduced to the minimum; in addition, the corrugated skirt can also prevent the belt crack. The material of the belt is an important factor affecting the normal operation of the belt. If the prestress of each layer and part of the belt core is not uniform during manufacturing, the phenomenon of different tightness and uneven stress will occur during the operation. Therefore, the (EP) skeleton material can be specially selected according to the belt length; compared with the nylon (NN) skeleton material, it has the characteristics of stable size, good heat stability, good water resistance, small change in dry and wet strength, light weight, etc., and the elongation can be controlled within 2%. The cleaning chain adopts wear-resistant precision casting, which mainly discharges the coal falling from the belt to the shell to prevent spontaneous combustion caused by coal accumulation.
1.3.2.6. Double cone main drive drum. The main drive drum is inclined, not perpendicular to the belt center line, and the outer surface processing error or uneven wear causes the diameter size. From time to time, the belt will deviate to the side with larger diameter, which is the so-called "running big but not running small". The production plant can adopt the double cone roller, that is, the roller with large middle diameter and small diameter at both ends, and strictly control the processing technology to ensure that the radial runout of the surface is not greater than 0.5mm, and the coaxiality of the shaft at both ends is not greater than 0.2mm, so as to effectively prevent the belt from running off the drum.
1.3.2.7. Cage driven roller. When machining the driven roller, the accuracy requirements should be met as same as that of the main drum, that is, the radial runout of the surface should not be greater than 0.5mm, and the coaxiality of the shafts at both ends should not be greater than 0.2mm. In addition, if the coal falling on the inner side of the belt can not be discharged in time, it will cause the coal feeder to deviate and the measurement will be unstable. Therefore, in practice, the cage driven drum is designed. The coal inside the belt falls onto the internal spiral plate through the cylinder with a long slot, and then the coal is rotated out during the rotation of the driven drum.
1.3.3. Maintenance mode of DPG series coal feeder. There are two ways of coal inlet and outlet, which can be divided into two types: direct draw-out and side draw-out.
1.3.3.1. Direct draw-out maitenance coal feeder. The belt transmission system and metering system are assembled on the coal conveying frame, which is like a "drawer". When replacing the belt or repairing the rolling, the "drawer" is pulled out from the rear end door and placed on the special maintenance spreader. This maintenance mode is easy to operate, reduces the maintenance workload, and is suitable for the coal feeder with the distance of coal feeding center less than 3.5m.
1.3.3.2. Side draw-out maintenance coal feeder. During maintenance, the main drum and idler are disassembled from the upper side door of the coal feeder housing, which is suitable for large center distance or insufficient maintenance space at the end door.
1.4. Working principle
In a typical coal combustion process, when the inlet coal gate is opened, the weighing feeder unloads the coal in the upper bunker and makes the coal fall on the belt through the outlet (the outlet has several optional sizes, including rectangular size). When the coal passes through the belt, the high-precision strain gauge sensor on the weighing scale frame is used to weigh the coal on the belt to determine the weight per meter of the coal on the belt; at the same time, the digital speed sensor is used to continuously measure the belt speed, and the pulse output of the speed sensor is directly proportional to the belt speed. Then, the speed signal and quality signal are sent to the microprocessor for accumulation processing, and the instantaneous flow rate in t/h is displayed digitally, and the accumulated mass of coal is displayed at the same time.
The belt drive motor is a frequency conversion motor, and the corresponding frequency converter is installed in the electrical cabinet. The PLC will compare the instantaneous flow of coal on the weighing scale frame with the coal feeding quantity required by combustion control, generate necessary output signal to the motor frequency converter, and change the belt speed of coal feeder to maintain the required coal flow. The coal is unloaded from the coal feeder and sent to the pulverizer through the chute and coal conveying pipe. In addition, DPG series coal feeder can also output remote signal to the centralized control room to realize remote automatic and remote manual adjustment of coal feeding amount.
2. Main technical parameters
Performance parameters of DPG series coal feeder are shown in table 18-1.
| Item | DPG30 | DPG40 | DPG50 | PC60 | PG80 | DPG100 | |
| Rated Output/capacity (t/h) | 30 | 40 | 50 | 60 | 80 | 100 | |
| Output range (t/h) | 3~35 | 4~46 | 5~55 | 5~70 | 8~90 | 10~115 | |
| Weighing accuracy (%) | ± 0.5 | ||||||
| Coal feeding distance (mm) | Based on the customer's requirement or the designing center requirement | ||||||
| Coal quality requirement | Density (t/m3) | 0.7~1.1 | |||||
| Particle | ≤60 | ||||||
| Moisture (%) | ≤21 | ||||||
3. Equipment appearance and structural dimensions
The outline and structural dimensions of DPC series coal feeder are shown in Figure 18-2 and table 18-2 respectively

Table 18-2 structural dimensions of DPG series coal feeder
| Dimensions Model |
Center distance | Coal inlet diameter | Coal feeder height | Coal gate height | Equipment width | Mounting base dimensions | Sealing air interface dimensions | |||
| L | ∮ | H | H1 | C | A | B | H2 | E | F | |
| DPG30~DPG100 | To be decided by design | 630 | 1513 | 200 | 1800 | L+1250 | 1300 | 1150 | 150 | 625 |
4. Selection method
We can select the type according to the coal feeding quantity proposed by the users, design and customize according to the requirements of the center distance of the coal inlet and outlet proposed by the user, or help the user select the coal feeder suitable for the output requirements of the coal mill according to the coal quality and working conditions provided by the user, and help the user determine the best scheme in terms of layout and maintenance mode.
5. Scope of supply and ordering instructions
5.1. Scope of supply (typical scope, which can be increased or decreased according to user's demand)
5.1.1. Coal feeder body (including belt conveyor, metering device, chain cleaning device, fully enclosed shell, alarm and protection device, etc.).
5.1.2. Inlet coal gate.
5.1.3. Outlet coal gate.
5.1.4. Coal fall pipe and flange connector at inlet and outlet.
5.1.5. Adjustable connector.
5.1.6. Control cabinet.
5.1.7. Special tools.
5.1.8. Random spare parts.
The scope of supply also includes the drawings, operation and maintenance manuals required for installation and commissioning.
5.2. Order requirements
It has the advantages of long service life, low coal consumption, long service life, low consumption of coal, electricity and so on. When selecting DPC series coal feeder, the user shall provide the following information:
5.2.1. Physical and chemical parameters of raw coal, including bulk density, particle size and moisture content of raw coal.
5.2.2. Form of pulverizing system and pulverizer.
5.2.3. Working pressure of coal feeder.
5.2.4. Layout position and form of equipment.
5.2.5. Coal feeding requirements.
5.2.6. Center distance between coal inlet and outlet.
5.2.7. Voltage, phase and frequency of the power supply provided.
5.2.8. Altitude, atmospheric conditions and other environmental factors.
5.2.9. Fire steam, sealing air and other parameters.
5.2.10. Fully consider the production cycle and define the delivery time.