PRODUCTS CENTER
Product Description
BBD double in and double out ball mill
1. Introduction
1.1. Purpose
It is mainly used for grinding, drying and separation of coal in direct fired pulverizing system of steam boiler in thermal power plant. The system is favored by power plant users because of its high degree of automation, wide adaptability of coal, high fineness of pulverized coal, easy maintenance and operation, and high requirements of modern large power plants.
1.2. Model meaning
BBD ** ##
BBD -- direct fired double inlet and double outlet ball mill
**----Cylinder length
##----Effective diameter of cylinder
1.3. Arrangement of coal mill (see figure 23-1, for reference only)

1.4. Arrangement of driving device of coal mill
From the driving side to the pulverizer, it can be divided into left mounting, right mounting, internal driving and external driving (see Fig. 23-2). The arrangement of the drive must be indicated when ordering.

1.5. Operation principle of double inlet and double outlet ball mill
The air powder flow of double inlet and double outlet ball mill is shown in figure 23-3. The raw coal is discharged from the hopper into the mixing box through the coal feeder with automatic speed control. After pre drying by the side air, the raw coal falls to the bottom of the screw conveyor through the coal dropping pipe, and the coal is sent into the rotating cylinder by the rotary movement of the screw propeller. The coal mill is driven by the main motor through the reducer and open gear to drive the cylinder to rotate. A certain amount of grinding medium steel ball is installed in the cylinder. The steel ball is lifted to a certain height by the rotating movement of the cylinder, and the steel ball grinds and grinds the coal in the process of free falling and throwing, until it is ground into pulverized coal.
The hot primary air is divided into two paths before entering the mill. On the one hand, the bypass air is mixed with raw coal in the mixing box to pre dry the coal; on the other hand, it keeps enough wind speed for conveying pulverized coal in the pulverized coal pipeline; The other way is to enter the mill air, which is used to transport and dry the pulverized coal in the cylinder. The mixture of air and powder in the cylinder is taken out of the pulverizer through the annular channel between the central pipe and the hollow pipe. The pulverized coal taken out of the pulverizer and the inlet air are mixed with the bypass air in the conveyor and then enter the separator; the separator is equipped with adjustable pulverized coal fineness blades, and the fineness of pulverized coal can be adjusted according to the requirements. The unqualified coal powder of coarse material is returned to the raw coal pipe by gravity, mixed with the raw coal for regrinding. After separated by the separator, the qualified pulverized coal is transported to the burner through the pulverized coal outlet and powder feeding pipe, and then injected into the boiler for combustion.
The unique feature of double inlet and double outlet ball mill is that there are two symmetrical and independent circuits, one of which can be used or two circuits can be used at the same time. Under the condition of low load operation, semi mill operation can be realized.
1.6. System control of coal mill
In order to ensure the normal operation of double in and double out ball mills, the whole system is equipped with the following five control loops:
1.6.1. Load control. Different from other types of coal mills, the output of double inlet and double outlet ball mills is not achieved by adjusting the operating speed of the coal feeder, but by adjusting the primary air flow into the pulverizer. No matter how the load of the boiler changes, the air coal ratio inside the pulverizer is always kept constant. Therefore, the flow of pulverized coal can be adjusted by changing the baffle position of the primary air system of the pulverizer and adjusting the primary air volume at the inlet of the pulverizer.
1.6.2. Coal level control. In order to maintain the coal level in the coal mill barrel at a certain height to obtain the best grinding effect of pulverized coal, the coal pulverizer is equipped with a differential pressure coal level measuring device, and the pressure difference related to the coal level can be tested at any time. When the coal level drops, the coal level signal is fed back to the coal feeder to improve the running speed of the coal feeder; otherwise, the speed of the coal feeder is reduced.
In the coal level control system, in addition to the differential pressure measurement, there is also a noise measurement device (electric ear) of the coal mill to supplement, and the noise measurement device and the differential pressure coal level measurement device are mutually standby.
1.6.3. Total air volume control of coal mill. The bypass air into the coal mixing box is responsible for maintaining sufficient air velocity for conveying pulverized coal in the pulverized coal pipeline under any pulverized coal flow. Therefore, the air volume control system specially designs a regulating unit to ensure the minimum air flow, and is also responsible for increasing the bypass air flow when the pulverized coal drying fails to meet the requirements.
1.6.4. Outlet temperature control of coal mill. The air / coal temperature at the outlet of the pulverizer should be kept at the highest possible temperature value for normal grinding process. In most grinding systems, the temperature range is usually set at 70 ~ 90C. The temperature can be adjusted by mixing the cold air and hot air of primary air according to different proportions. The regulating system directly acts on the cold air baffle, and the opening degree of the hot air baffle has been set according to the requirements, that is, when the opening degree of the cold air baffle is adjusted arbitrarily, the hot air volume should be 30% - 80% of the total air volume.
1.6.5. Primary air pressure control. Under a certain output of the pulverizer, the primary air pressure must be maintained within the required range to ensure the pulverized coal to be exported to the pulverizer. Therefore, a pressure control system is specially set up to maintain the primary air pressure within a certain range by adjusting the opening degree of fan blades.
1.7. Structural features of double in and double out ball mills
The coal mill is composed of barrel part, screw conveyor, separator, main bearing, main transmission device, auxiliary transmission device, sealing system, coal mixing box, ball adding device, sound insulation cover, pulverized coal cut-off valve and other equipment.
1.7.1. Spherical self-aligning main bearing. The main bearing is used to support the rotary cylinder and compensate the sag of the cylinder under load. It is composed of bearing bush, bearing seat and spherical body.
1.7.2. Screw conveyor. The screw conveyor is composed of screw propeller and conveyor shell. The propeller is composed of blade, chain and central pipe. The end of the screw propeller is connected with the cylinder by four supporting rods, and the other end is supported by the external bearing of the conveyor shell. When the cylinder rotates, the screw propeller is driven to rotate, and the raw coal is pushed into the cylinder body through the blades.
1.7.3. Cylinder part. The cylinder part is mainly composed of hollow shaft, end cover, cylinder and lining plate. When the cylinder rotates, the steel ball in the cylinder impacts and grinds the raw coal under the lifting of the liner.
1.7.4. Separator. The separator is composed of separator shell, inner cone and blade adjusting device. The inner wall of the separator is lined with wear-resistant lining, and its blade adjusting device can be used to adjust the fineness of pulverized coal.
1.7.5. Main drive. The main transmission device is composed of main motor, main reducer, small gear device and big gear. The main driving device is used for the normal operation of coal mill.
1.7.6. Auxiliary drive. The auxiliary transmission device is composed of motor, reducer and overrunning clutch. During operation, the mill barrel rotates at 1 / 100 of the rated speed, which is mainly used for the start-up, stop and maintenance of the mill.
1.7.7. Coal mixing box. The function of coal mixing box is to pre dry raw coal. In order to prevent corrosion, some materials in the coal mixing box are made of stainless steel.
1.7.8. Pulverized coal shut-off valve. The pulverized coal shut-off valve is used to completely isolate the boiler from the pulverizer. Generally, the pulverized coal shut-off valve is composed of valve body, cylinder or electric actuator, and is located at the outlet of separator.
1.7.9. Ball adding device. The ball feeding device is composed of ball storage tank, upper and lower gate valves and pipes, which are usually placed on the same level of coal feeder. Due to the special measures adopted in the structure, the ball adding can be realized without stopping the mill.
1.7.10. Sealing system. The sealing system consists of fans, valves and pipes. The system provides sealing air higher than the pressure in the mill to seal the dynamic and static parts of the mill to prevent the leakage of pulverized coal in the mill.
1.7.11. Acoustic enclosure. The sound insulation cover is composed of metal frame, thin steel plate, mineral wool, etc. The use of acoustic enclosure can effectively isolate the noise generated by coal mill and avoid environmental pollution.
1.8. Main performance characteristics of double in and double out ball mills
1.8.1. The continuous operation rate is high. The ball of wearing parts can be added without stopping the machine. The life span of propeller blade is 3 ~ 5 years, and that of cylinder liner is 4 ~ 7 years. As long as the boiler does not stop running, the mill can run for a long time.
1.8.2. The response is rapid in wide load range. The capacity of coal stored in the mill is large, and the output is directly proportional to the primary air volume, so that the response speed of the mill is very fast.
1.8.3. Less maintenance times. There is no need to stop for maintenance during the operation period of coal mill. The replacement of spiral blade and cylinder liner can be carried out along with boiler maintenance, so the maintenance cost of coal mill is greatly reduced.
1.8.4. The air coal ratio is low. The low air coal ratio is determined by the structure of the coal mill itself. The low ratio of air to coal increases the concentration of pulverized coal in the primary air, and the fineness of low load increases, which makes the minimum load of the boiler lower in the case of coal combustion. As a result, the maintenance load can be reduced and expensive gas or oil can be used.
The output and fineness are stable. The output of coal mill is regulated by the change of primary air volume. If the primary air volume remains unchanged, the output is constant. Since the output control and the coal quantity control in the mill are independent, the coal quantity in the pulverizer will not be affected by the increase of output. The fineness of pulverized coal is usually determined by the amount of steel balls in the mill
1.8.6. The range of grinding coal is wide. The grinding mechanism of coal mill determines that the mill can adapt to all kinds of coal quality, especially for lean coal with high ash content, high wear index and low volatile matter.
1.8.7. The ability to grind hard and highly abrasive fuels. During grinding, it is the liner plate and steel ball that are worn. Lining plate life is generally very long, and according to the characteristics of coal can choose the corresponding material to improve wear performance.
1.8.8. Not affected by foreign matters. The double in and double out steel ball mill has a strong adaptability to the "three pieces" (iron, wood and stone). As long as the size is not large, the "three pieces" can be used as grinding media to grind together in the mill, so the operation of the mill will not be affected.
1.8.9. Large storage capacity. Generally, the coal quantity is 15% of the ball loading capacity, which is equivalent to 1 / 4H work load under the rated load of the coal mill. The output of the coal mill will not be affected if the coal is not supplied for a short period of time or the coal is supplied on one side. The response speed of coal mill from low load to high load is very fast, and the response time is within 15s.
The fineness increases under low load. At low load, the coal stays in the mill for a long time and the fineness increases, which is very beneficial to the boiler combustion, especially the flame stability is better under low load
1.8.11. According to the load requirements, the double in and double out ball mill can operate in three working conditions: double in and double out, single in and double out, and semi mill operation. This will bring more convenience to users in practical application.
2. Main technical parameters
The main technical and performance parameters of the coal mill are shown in table 23-1 ~ table 23-3.
Table 23-1 main technical parameters of coal mill
| No. | Model | Effective diameter of the cylinder (mm) | Effective length of the cylinder (mm) | working speed (r/min) | Basic output (t/h) | Max.ball filling (t) | Motor power (Kw) | Equipment weight (t) |
| 1 | BBD3448 | 3350 | 4940 | 18 | 35 | 53.6 | 830 | 158 |
| 2 | BBD3854 | 3750 | 5540 | 17 | 52 | 70 | 1200 | 205 |
| 3 | BBD4060 | 3950 | 6140 | 16.6 | 62 | 83.9 | 1500 | 230 |
| 4 | BBD4360 | 4250 | 6140 | 16 | 75 | 99 | 1800 | 260 |
| 5 | BBD4366 | 4250 | 6740 | 16 | 82 | 108 | 2000 | 270 |
| 6 | BBD4760 | 4650 | 6140 | 15.3 | 88 | 116.3 | 2200 | 310 |
| 7 | BBD4772 | 4650 | 7340 | 15.3 | 107 | 139 | 2600 | 360 |
Note: the basic output in the table refers to the production capacity under the standard coal, that is, the Hardgrove grindability index is 50, the total moisture coal moisture is 10%, and the fineness of pulverized coal is 75%, passing through 200 mesh
Table 23-2 general working range of coal mill
| Performance parameters | BBD models | ||||||
| 3448 | 3854 | 4060 | 4360 | 4366 | 4760 | 4772 | |
| Ball load range B1 (t) | 26 | 36 | 45 | 50 | 54 | 63 | 75 |
| Ball load range B2 (t) | 48 | 63 | 76 | 89 | 97 | 100 | 122 |
| Maximum ball load Bmax (t) | 53.6 | 70 | 83.9 | 99 | 108 | 116.3 | 139 |
| Raw coal flow P2 of each mill (t/h) | 36 | 52 | 62 | 75 | 82 | 88 | 107 |
Note: the coal quality and steel ball load corresponding to P2 are as follows: HGI is 50, 75% passing through 200 mesh, total moisture final moisture is 10%, steel ball load is B2
Table 23-3 power consumption of coal mill
| Performance parameters | BBD mill model | ||||||
| 3448 | 3854 | 4060 | 4360 | 4366 | 4760 | 4772 | |
| W0 (Kw) | 479 | 713 | 898 | 1079 | 1185 | 1351 | 1615 |
| Ball max load (t) | 53.6 | 70 | 83.9 | 99 | 108 | 116.3 | 139 |
| Corresponding filling rate (%) | 0.246 | 0.229 | 0.223 | 0.227 | 0.227 | 0.223 | 0.223 |
| Vmax (Kw) | 741 | 1034 | 1273 | 1553 | 1705 | 1915 | 2289 |
3. Main structural dimensions
The dimension code and installation dimension of BBD double inlet and double outlet ball mill are shown in figure 23-4 and table 23-4 respectively

Table 23-4 installation dimensions of coal pulverizer
| Dimensions code | Model | ||||||
| BBD3448 | BBD3854 | BBD4060 | BBD4360 | BBD4366 | BBD4760 | BBD4772 | |
| A | 2796.5 | 3029.6 | 3154.7 | 3268.1 | 3268.1 | 3657.2 | 3657.2 |
| B | 765 | 860 | 1000 | 1080 | 1080 | 1080 | 1080 |
| C | 5150 | 5750 | 6350 | 6350 | 6950 | 6360 | 7560 |
| D | ∮3490 | ∮3896 | ∮4096 | ∮4404 | ∮4404 | ∮4820 | ∮4820 |
| E | 1170 | 1197.5 | 1222.5 | 1222.5 | 1222.5 | 1290 | 1290 |
| F | 1100 | 1115 | 1132.5 | 1152.5 | 1152.5 | 1230 | 1230 |
| G | 7420 | 8050 | 8685 | 8725 | 9325 | 8900 | 10100 |
| H | 4880 | 5222.5 | 5565 | 5585 | 5885 | 5740 | 6340 |
| J | ∮2100 | ∮2400 | ∮2900 | ∮3200 | ∮3200 | ∮3500 | ∮3500 |
| K | 6390 | 6730 | 6800 | 7100 | 7400 | 7300 | 7900 |
| L | 2750 | 2800 | 2800 | 2900 | 2900 | 3200 | 3200 |
| M | 1800 | 2270 | 2270 | 2270 | 2270 | 2800 | 2800 |
| N | 1000 | 1010 | 1060 | 1155 | 1155 | 1250 | 1250 |
| P | 3200 | 3400 | 3500 | 3700 | 3700 | 4200 | 4200 |
| Q | 12600 | 12600 | 12600 | 13700 | 13700 | 13700 | 13700 |
| R | 14000 | 14000 | 14200 | 15400 | 15400 | 16000 | 16000 |
4. Selection calculation
4.1. Determination of coal mill model
The determination of the maximum raw coal flow Pmax . Pmax is the maximum raw coal flow rate of each pulverizer after the required fineness of coal and considering the control coefficient of 5%.
Example: Pd = 95000 kg/h; Pw=114000 kg/h
Scheme 1: three coal mills are installed and two are in operation (N=2, coal type is not limited).


Therefore, Pmax2 > Pmax1, Pmax2 is the maximum raw coal flow rate, and Pmax2 must be considered in the selection of coal mills
Where Pd ---- the consumption of each boiler in the design coal type, kg/h;
Pw ---- consumption of each boiler when checking coal type, kg/h;
N ---- the number of mills in operation of each boiler;
Pmax ---- maximum raw coal flow of each mill
Scheme 2: install three coal mills, two for design coal and three for check coal.


Therefore, Pmax1 > Pmax2, Pmax1 is the maximum raw coal flow rate, Pmax1 must be considered in the selection of pulverizer.
4.2. Calculation of shaft power of coal mill
4.2.1. Calculation of ball filling rate of coal mill. The filling rate of coal mill refers to the ratio of ball load volume to effective volume of high body of coal mill, i.d.

Where R ---- the filling rate;
VB ---- load volume of steel ball, m3;
Vm ---- effective volume of cylinder, m3.
The relationship between ball load and filling rate is as follows


Where
D -- effective diameter of mill, m,
L -- effective length of mill, m;
B -- steel ball load, t.
The average density of steel ball load is considered as 5t/m3.
It can be seen from the above formulas that when the ball load force of BBD4772 coal mill is 100t, the filling rate

4.2.2. Calculation of shaft power of coal mill.
The calculation formula of shaft power is
W=W0 ƒ(R)
Where W -- shaft power consumed by coal mill;
R -- filling rate of coal mill.
W0 depends on the type of coal mill, where ƒ(R)= 5.714R + 0.143
Therefore, for BBD4772 coal mill, when the ball load is 100t , the allowable filling rate R=0.16 and W0 = 1615kW, there are
ƒ(R) = 5.714 × 0.16 + 0.143 = 1.057
W = 1615 × 1.057 = 1707 kW
4.3. Power consumption
When calculating the electric power consumed by coal mill, the efficiency of motor and reducer should be considered. For example, for BBD4772 coal mill, when the ball load is 100t, the motor efficiency of the pulverizer is 95%, the reducer power is 98%, and the shaft power consumed by the pulverizer is 1707kw (see the calculation example of shaft power above), the electric power consumed by the coal mill can be calculated as

4.4. Determination of motor power
4.4.1. Determine the maximum shaft consumption power Wmax, at this time, the ball loading capacity of the pulverizer corresponds to the maximum raw coal flow according to the designed coal type.
4.4.2. Calculate the maximum shaft power consumption W* max on the high-speed shaft of the main reducer. W* max the calculation formula is

4.4.3. Determine the power required by the motor. The power required by the motor is We, the formula is
We = 1.1W* max
5. Scope of supply
The scope of supply is usually from the outlet of the coal feeder to the outlet of the separator, including the pulverized coal gate at the outlet of the separator