PRODUCTS CENTER
Sri Lanka 2SA3 series multi rotary electric actuator
Category:
Product Description
2SA3 series multi rotary electric actuator
1. Introduction
1.1. Purpose
2SA3 series multi rotary electric actuator is used to control gate valve, globe valve, throttle valve and diaphragm valve.
1.2. Model meaning
Code Position 5 67 8 9 10 11 12 13 14 15 16
2SA3 ** ## - $$ @@ && ** ※※ - §§ ¢¢ ☆☆ □□ +Z additional special selection code
Code of 2SA3 --- 2SA3 series multi rotary electric actuator
**----------Executive machinery series (Code position 5)
##------------Frame number and torque grading (Code position 6,7)
$$--- output connection form (Code position 8)
@@------------------Output shaft speed (Code position 9)
&&---------------------Motor (Code position 10)
**-------------Motor thermal protection (Code position 11)
※※---------Protection sleeve of valve stem (Code position 12)
§§---------Power control unit (Code position 13)
¢¢------Signal components (Code position 14)
☆☆-------Switch and signal contact (Code position 15)
□□---------Wiring mode (Code position 16)
1.2.1. Selection of actuator series (code point 5).
0: S series, switch type, i.e. 2SA30 series electric actuator, is used for open-loop control system. The motor standard is S2, 15min (short time intermittent working system);
5: R series, regulation system, i.e. 2SA30 series electric actuator, is used for closed control system. The motor standard is S4 or S5 (intermittent working system), the minimum load sustained rate is 10%, and the maximum working times is 1200 times / h.
1.2.2. See table 57-1 to table 57-4 for the selection of frame number and torque grading (code positions 6 and 7)
Table 57-1 output torque series I (standard output) of S Series (2SA30 Series)
| Code position 6, 7 | Output control torque range (N.m) | Flange number (according to GB 12222) | Flange number (according to JB 2920) |
| 10 | 10~30 | F07 | 1,2 |
| 11 | 10~30 | F10 | 1, 2 |
| 12 | 20~60 | F10 | 1, 2 |
| 20 | 40~125 | F10 | 1, 2, 3, 2 (Ⅰ) |
| 21 | 40~125 | F14 | 1, 2, 3, 2 (Ⅰ) |
| 22 | 80~250 | F14 | 1, 2, 3, 2 (Ⅰ) |
| 30 | 160~500 | F14 | 2, 3, 4, 5 |
| 31 | 16o~500 | F16 | 2, 3, 4, 5 |
| 32 | 315~1000 | F16 | 2, 3, 4, 5 |
| 40 | 630~2000 | F25 | 4, 5, 7, 8 |
| 41 | 630~2000 | F30 | 4, 5, 7, 8 |
| 42 | 1250~4000 | F30 | 4, 5, 7, 8 |
Note 1. The output torque of 2SA30 series electric actuator is generally implemented according to table 57-1, and the special requirements can be implemented according to table 57-2 of output torque II, but it must be in the additional optional code - Y01 on the model.
2. GB 12222 is the latest standard GB 12222-2005 connection of multi turn valve driving device.
Table 57-2 second output torque series of S Series (2SA30 Series)
| Code position 6, 7 | Output control torque range (N.m) | Flange number (according to GB 12222) | Flange number (according to JB 2920) |
| 12 | 24~72 | F10 | 1, 2 |
| 22 | 100~300 | F14 | 1, 2, 3, 2 (I) |
| 32 | 400~1200 | F16 | 2, 3, 4, 5 |
| 42 | 1600~4800 | F30 | 4, 5, 7, 8 |
Table 57-3 output torque series I of R series (2SA35 Series) (standard output)
| Code position 6, 7 | Output control torque range (N.m) | Flange number (according to GB 12222) |
| 10 | 15~20 | F07 |
| 11 | 15~20 | F10 |
| 12 | 30~40 | F10 |
| 20 | 60~80 | F10 |
| 21 | 60~80 | F14 |
| 22 | 125~175 | F14 |
| 30 | 250~350 | F14 |
| 31 | 250~350 | F16 |
| 32 | 500~700 | F16 |
| 40 | 1000~1400 | F25 |
| 41 | 1000~1400 | F30 |
| 42 | 2000~2800 | F30 |
Note: the output torque of 2SA35 electric actuator is generally implemented according to table 57-3, and the special requirements can be implemented according to table 57-4 of the second output torque, but the optional code - Y01 must be added on the model.
Table 57-4 output torque series Ⅱ of R series (2SA35 Series)
| Code position 6, 7 | Output control torque range (N.m) | Flange number (according to GB 12222) |
| 10 | 10~15 | F07 |
| 11 | 10~15 | F10 |
| 12 | 20~30 | F10 |
| 20 | 40~60 | F10 |
| 21 | 40~60 | F14 |
| 22 | 80~120 | F14 |
| 30 | 180~250 | F14 |
| 31 | 180~250 | F16 |
| 32 | 300~500 | F16 |
| 40 | 700~1000 | F25 |
| 41 | 700~1000 | F30 |
1.2.3. Output connection form (code position 8)
0: according to the provisions of GB12222 (Figure 57-1 and table 57-5, figure 57-2 and table 57-6), it can not only transfer torque, but also bear capacity.

Table 57-5 flange connection dimensions
| Model 2SA3×× | 10 | 11 , 12 | 20 | 21 , 22 | 30 | 31 , 32 | 40 | 41 , 42 |
| Flange No. | F07 | F10 | F14 | F16 | F25 | F30 | ||
| d1 | 90 | 120 | 175 | 205 | 300 | 350 | ||
| d2 | 55 | 70 | 100 | 130 | 200 | 230 | ||
| d3 | 70 | 102 | 140 | 165 | 254 | 298 | ||
| d4 | M8 | M10 | M16 | M20 | M16 | M20 | ||
| h1 | 20 | 25 | 22 | 30 | ||||
| h | 3 | 4 | 5 | |||||
| n | 4 | 8 | ||||||
| α/2 | 45° | 22.5° | ||||||
Table 57-6 output end dimensions of output shaft that can transfer torque and thrust
| Model 2SA3×× | 11 , 12 | 20 | 21 , 22 | 30 | 31 , 32 |
| Flange No. | F10 | F14 | F16 | ||
| d5 | 32 | 53 | 53 | 72 | 72 |
| d6 | 30 | 50 | 50 | 70 | 70 |
| L | 40 | 54 | 54 | 75 | 75 |
| h | 40 | 79 | 54 | 97 | 76 |
1: It is only used for 2SA30 as specified in table 57-7, figure 57-3 and table 57-8

Table 57-7 connecting flange number
| Additional code Flange number model |
J01 | J1A | J2A | J3A |
| 2SA3.1 | 1 | 2 | - | - |
| 2SA3.2 | 1 | 2 (Ⅰ) | 2 | 3 |
| 2SA3.3 | 2 | 3 | 4 | 5 |
| 2SA3.4 | 4 | 5 | 7 | 8 |
Table 57-8 side joint dimensions
| Flange No. | 1 | 2 | 2(Ⅰ) | 3 | 4 | 5 | 7 | 8 | 9 | 10 |
| D | 115 | 145 | 115 | 185 | 225 | 275 | 330 | 380 | 430 | 510 |
| D1 | 95 | 120 | 95 | 160 | 195 | 235 | 285 | 340 | 380 | 450 |
| D2(H9) | 75 | 90 | 75 | 125 | 150 | 180 | 220 | 280 | 300 | 360 |
| h1 | 2 | 3 | ||||||||
| f | 5 | 6 | 8 | |||||||
| h | 6 | 8 | 6 | 10 | 12 | 14 | 16 | 20 | 25 | 30 |
| b | 10 | 12 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
| d1 | 20 | 30 | 26 | 42 | 50 | 62 | 65 | 80 | 85 | 105 |
| d2 | 28 | 45 | 39 | 58 | 72 | 82 | 98 | 118 | 128 | 158 |
| d | M8 | M10 | M8 | M12 | ∮18 | ∮22 | ∮26 | ∮22 | ∮26 | ∮33 |
| n | 4 | 8 | ||||||||
2: According to GB 12222 (Fig. 57-1 and table 57-5, Fig. 57-4 and table 57-9), only transfer torque (for rising stem valve).

Table 57-9 output size of torque transfer only
| Flange No. | F07 | F10 | F14 | F16 | F25 | F30 |
| d5 | 25 | 32 | 53 | 75 | 115 | 115 |
| d7(H9) | 28 | 42 | 60 | 80 | 100 | 120 |
| b1(JS9) | 8 | 12 | 18 | 22 | 28 | 32 |
| t1(+0.2) | 31.3 | 45.3 | 64.4 | 85.4 | 106.4 | 127.4 |
| h1 | 1.2 | 1.3 | 2.1 | 2.1 | 2 | 2 |
| L | 36 | 46 | 67 | 82 | 139 | 139 |
3: C type hollow shaft with jaw clutch, according to DIN3338 (table 57-10).
Table 57-10 connection size of special code selection connection form
| GB 12222 | Code position 6 , 7 | 10 | 11 , 12 | 20 | 21 , 22 | 30 | 31 , 32 | 40 | 41 , 42 | ||||
![]() |
GB12222 | F07 | F10 | — | F10 | — | F14 | F14 | F16 | F25 | — | F30 | — |
| DIN3210 | — | — | 0 | — | 0 | 1/2 | 1/2 | 3 | — | 4 | — | 5 | |
| d1 | 90 | 120 | 120 | 120 | 120 | 175 | 175 | 205 | 300 | 300 | 350 | 350 | |
| d2 | 55 | 70 | 60 | 70 | 60 | 100 | 100 | 130 | 200 | 160 | 230 | 180 | |
| d3 | 70 | 102 | 102 | 102 | 102 | 140 | 140 | 165 | 254 | 254 | 298 | 300 | |
| d4 | M8 | M10 | M10 | M10 | M10 | M16 | M16 | M20 | M16 | M16 | M20 | M20 | |
| Z | 4 | 4 | 4 | 4 | 4 | 4 | 4 | 4 | 8 | 8 | 8 | 8 | |
| H | 3 | 3 | 3 | 3 | 3 | 4 | 4 | 5 | 4 | 4 | 4 | 4 | |
| h3 | 20 | 20 | 20 | 20 | 20 | 25 | 22 | 30 | 30 | 30 | 30 | 30 | |
| h5 | — | 8 | 8 | — | — | 11 | — | 20 | — | — | — | — | |
| Type A hollow shaft with threaded sleeve DIN3210 | GB12222 | F07 | F10 | F10 | F14 | F14 | F16 | F25 | F30 | ||||
![]() |
DIN3210 | — | 0 | — | 1/2 | 1/2 | 3 | 4 | 5 | ||||
| Max. thrust(KN) | — | 40 | 40 | 100 | 100 | 150 | — | — | |||||
| d5 | — | 32 | 53 | 53 | 72 | 72 | — | — | |||||
| d6,max | — | 30 | 50 | 50 | 70 | 70 | — | — | |||||
| L | — | 40 | 54 | 54 | 75 | 75 | — | — | |||||
| L2 | — | 251 | 359 | 334 | 319 | 298 | — | — | |||||
| h | — | 40 | 79 | 54 | 97 | 76 | — | — | |||||
| Type B1 hollow shaft with keyway DN3210 | d5 | 25 | 32 | 39 | 53 | 56 | 75 | 115 | 115 | ||||
![]() |
d7 | 28 | 42 | 42 | 60 | 60 | 80 | 100 | 120 | ||||
| b1 | 8 | 12 | 12 | 18 | 18 | 22 | 28 | 32 | |||||
| t1 | 31.3 | 45.3 | 45.3 | 64.4 | 64.4 | 85.4 | 106.4 | 127.4 | |||||
| L1 | 36 | 46 | 46 | 67 | 67 | 82 | 139 | 139 | |||||
| h1 | 1.2 | 1.3 | 1.4 | 2.1 | 2.1 | 2.1 | 2 | 2 | |||||
| L2 | 239 | 239 | 318 | 318 | 258 | 258 | 346 | 346 | |||||
| Type B3 hollow shaft with keyway DN3120 | d10 | 16 | 20 | 20 | 30 | 30 | 40 | 50 | 60 | ||||
![]() |
b4 | 5 | 6 | 6 | 8 | 8 | 12 | 14 | 18 | ||||
| t3 | 18.3 | 22.8 | 22.8 | 33.3 | 33.3 | 43.3 | 53.3 | 64.4 | |||||
| L1 | 36 | 46 | 46 | 67 | 67 | 82 | 139 | 139 | |||||
| h1 | 1.9 | 1.5 | 2.1 | 2.1 | 2.1 | 2.1 | 2 | 2 | |||||
| Type C hollow shaft with teeth-clutch DIN3210, DIN3338 | d12 | — | 42 | 42 | 60 | 60 | 80 | 120 | 120 | ||||
![]() |
d11 | — | 28 | 28 | 38 | 38 | 47 | 64 | 75 | ||||
| b1 | — | 14 | 14 | 20 | 20 | 24 | 30 | 40 | |||||
| h1 | — | 1.5 | 2.1 | 2.1 | 2.1 | 2.1 | 2 | 2 | |||||
| h11 | — | 9 | 9 | 10 | 10 | 12 | 11 | 13 | |||||
| L2 | — | 239 | 318 | 318 | 258 | 258 | 346 | 346 | |||||
| Type D additional shaft with keyway DIN3210 | d8 | — | 20 | 20 | 30 | 30 | 40 | 50 | 60 | ||||
![]() |
L4 | — | 50 | 50 | 70 | 70 | 90 | 110 | 120 | ||||
| L5 | — | 55 | 55 | 76 | 76 | 97 | 117 | 127 | |||||
| b3 | — | 6 | 6 | 8 | 8 | 12 | 14 | 18 | |||||
| t2 | — | 22.5 | 22.5 | 33 | 33 | 43 | 53.5 | 64 | |||||
5: According to GB 12222 (Fig. 57-1 and table 57-5, Fig. 57-5 and table 57-11), only transfer torque (for Non rising stem valve).

Table 57-11 size of output torque output end
| Flange No. | F07 | F10 | F14 | F16 | F25 | F30 |
| d10(H9) | 16 | 20 | 30 | 40 | 50 | 60 |
| b4(JS9) | 5 | 6 | 8 | 12 | 14 | 18 |
| t3(+0.2) | 18.3 | 22.8 | 33.3 | 43.3 | 53.3 | 64.4 |
| 1h1 | 3 | 3 | 4 | 5 | 5 | 5 |
| L1 | 35 | 45 | 65 | 80 | 110 | 130 |
9: According to DIN3210 or other non-standard special connection forms.
DIN3210 is connected in five forms (see table 57-10). Optional code (- H10A, - H2A, - H3A, - H4A, - H5A) can be added after 16 bit code. Optional code Y04 is required for other non-standard special connection forms.
1.2.4. Output shaft speed (code position 9)
B:5r/min; H:40r/min; C:7r/min; J: 56r/min; D:10r/min; K:80r/min; E:14r/ min: L :112r/min; F: 20r/min;M: 160r/min;G:28r/min。
There is no speed above 56 r/min in 2SA304; there is no speed above 14r/min and 112r/min in the second output torque of S series; there is no speed above 40r/min in 2SA3042; the maximum speed of R series is 40r/min.
1.2.5. Motor (code position 10)
A: No mechanical brake; 380V, 50Hz.
1.2.6. Thermal code (code position 11).
0: thermal control switch (R series has no choice); 1: PTC thermistor.
1.2.7. Stem protection sleeve (code position 12)
0: no protective cover; 1: with protective cover; 9: special protective cover (in two forms, optional code - M1A, - M2A can be added after 16 bit code)
1.2.8. Power control module (code point 13)
0: no power control module;
1: Sn control module (non intrusive, 2SA35 Series);
6: Sn control module (non intrusive, 2SA30 Series);
9: With other power control modules. Other power control modules can add LKO, - MKO, - MUO, - MDO after 16 bit code.
1.2.9. Signal component (code position 14)
0: noninvasive (when the 13th digit is 1 or 6);
A: No mechanical position indicator, no signal gear assembly:
B: Without mechanical position indicator, the potentiometer RP is 100 Ω (without power control module);
C: No mechanical position indicator, electronic position transmitter (ESR) two-wire;
D: No mechanical position indicator, ESR three wire;
E: With mechanical position indicator, no signal feedback component;
F: With mechanical position indicator, RP is 100 Ω (without power control module);
G: With mechanical position indicator, ESR second line;
H: Mechanical position indicator, ESR three wire.
1.2.10. Switch and signal contact (code position 15).
0: non intrusive (when the 13th bit is 1 or 6)
A: Silver contact, 2DE + 2WE (counter type);
B: Silver contact, 2DE + 4WE (counter type);
C: Silver contact, 2DE + 6WE (counter + 2 cam discs);
J: Silver contact, 4DE + 2WE (counter type);
K: Silver contact, 4DE + 4WE (counter type);
L: Silver contact, 4DE + 6WE (counter + 2 cam discs).
Note: DE refers to the switch assembly of torque control mechanism; we refers to the switch assembly of stroke control mechanism.
1.2.11. Wiring mode (code position 16)
0: noninvasive (when the 13th digit is 1 or 6);
1: Terminal, screw connection:
2: Connector
1.2.12. Additional special selection code.
H0A: special connection type according to DIN3210 standard, A type a hollow shaft with threaded sleeve;
H2A: special connection form according to DIN3210 standard, B1 hollow shaft with keyway (rising stem valve);
H3A: special connection form according to DIN3210 standard, C-type hollow shaft with jaw clutch;
H4A: special connection type according to DIN3210 standard, D-type additional shaft with keyway;
H5A: special connection form according to DIN3210 standard, B3 type hollow shaft with keyway (Non rising stem valve);
MUO: integrated with digital power control module (R Series);
MDO: integrated with digital single-phase power control module;
LKO: integrated with motor control module;
MKO: integrated with digital power control module;
M1A: length of protective sleeve, 2SA3.1:250mm; 2SA3.2:500mm; 2SA3.3:750mm; 2SA3.4:1000mm;
M2A: length of protective sleeve, 2SA3.1:500mm; 2SA3.2:750mm; 2SA3.3:1000mm;
Y01: the electric actuator is executed according to the second output torque table;
Y02: adjust the maximum number of turns according to the user's requirements, and the adjustment range is 0.9, 2.3, 6, 15, 38 and 100r / stroke;
Y05: adjust the maximum number of turns according to the user's requirements, the adjustment range is 650, 1650, 4200r / stroke (normal 250r)/
Travel time);
Y30: the left (counterclockwise) direction of the output is the closing direction;
Y40: other non-standard special connection forms;
H01: with space heater (5.6k Ω, 220VAC)
Note: when additional special selection code, add "- Z" after standard 16 bit code and then add special selection code.
Example: with space heater, the model is 2SA3 ××× - 1 ××× - ××××× - ZH01; the connection form is H0A in DIN3210 and with space heater, the model is 2SA3 ×× - 9 ××× - ××××××× ZH0A + H01
1.3. Structural features
2SA3 series multi rotation electric actuator consists of six parts, namely special motor, worm gear reducer with hand wheel, hand electric switching mechanism, switch and signal part, electric actuator connection part and electrical part. According to the user's requirements, it can be equipped with the corresponding control module, or the non-invasive electric actuator with built-in control module can be selected.
The motor motion is transmitted to the output shaft after the worm gear pair decelerates to form the multi rotation motion of the output shaft, and then the multi rotation motion of the output shaft is transmitted to the switch and signal part after the spiral gear pair decelerates; At the same time, due to the influence of reaction force, the worm moves axially while rotating, and the torque signal is transmitted to the switch and signal part through the crank, and the valve position and torque signal are output by the switch and signal part.
2. Main technical parameters and product appearance
2.1. Main technical parameters (see table 57-12 and table 57-13)
Table 57-12 performance parameters of 2SA30 series electric actuators (the first output torque series)
| Multi rotary electric actuator | ![]() |
|
|||||||||||||||||||||||
| S series | Model | 2SA3010 | 2SA3011 | 2SA3012 | 2SA3020 | 2SA3021 | 2SA3022 | 2SA3030 | 2SA3031 | 2SA3032 | 2SA3040 | 2SA3041 | 2SA3042 | ||||||||||||
| Control torque (N.m) | Max. | 30 | 60 | 125 | 250 | 500 | 1000 | 2000 | 4000 | ||||||||||||||||
| Min. | 10 | 20 | 40 | 80 | 160 | 315 | 630 | 1250 | |||||||||||||||||
| Output speed (r/min) | 5, 7, 10, 14, 20, 28, 40, 56, 80, 112, 160 | 5, 7, 10, 14, 20, 28, 40 | |||||||||||||||||||||||
| Flange No. (according to GB12222) | F07 | F10 | F14 | F16 | F25 | F30 | |||||||||||||||||||
| Flange No. (according to JB2920) | 1, 2 | 1, 2, 2(I)3 | 2, 3, 4, 5 | 4, 5, 7, 8 | |||||||||||||||||||||
| Motor | Working system | S2, 15min | |||||||||||||||||||||||
| Type | Three phase asynchronous motor, insulation class F | ||||||||||||||||||||||||
| Power(kW) | 0.03~0.12 | 0.06~0.25 | 0.12~0.55 | 0.25~1.1 | 0.37~4 | 0.75~7.5 | 1.5~7.5 | 3~15 | |||||||||||||||||
| Weight(Kg) | 26 | 27 | 50 | 54 | 110 | 115 | 220 | 235 | |||||||||||||||||
Note: see table 57-2 for the second output torque series
Table 57-13 performance parameters of 2SA35 series electric actuators (the first output torque series)
| Multi rotary electric actuator | |
|
|||||||||||||||||||||||
| R series | Model | 2SA3510 | 2SA3511 | 2SA3512 | 2SA3520 | 2SA3521 | 2SA3522 | 2SA3530 | 2SA3531 | 2SA3532 | 2SA3540 | 2SA3541 | 2SA3542 | ||||||||||||
| Control torque (N.m) | Max. | 20 | 40 | 80 | 175 | 350 | 700 | 1400 | 2800 | ||||||||||||||||
| Min. | 15 | 30 | 60 | 125 | 250 | 500 | 1000 | 2000 | |||||||||||||||||
| Output speed (r/min) | 5, 7, 10, 14, 20, 28, 40 | 5, 7, 10, 14 | 5, 7, 10 | ||||||||||||||||||||||
| Flange No. (according to GB12222) | F07 | F10 | F14 | F16 | F25 | F30 | |||||||||||||||||||
| Motor | Working system | S4 or S5 (intermittent working system), the minimum continuous load is 10%, and the maximum working times is 1200 times / h | |||||||||||||||||||||||
| Type | Three phase asynchronous motor with and without brake, insulation class F, with PTC thermistor | ||||||||||||||||||||||||
| single-phase motor | |||||||||||||||||||||||||
| Power(kW) | 0.03~0.12 | 0.06~0.55 | 0.12~0.75 | 0.25~1.1 | 0.55~2.2 | 1.1~4.0 | 2.2~4.0 | 4~5.5 | |||||||||||||||||
| Weight(Kg) | 26 | 27 | 50 | 55 | 110 | 115 | 220 | 235 | |||||||||||||||||
Note: see table 57-4 for the second output torque series
2.2. Product appearance
The outline of 2SA3 series multi rotation electric actuator is shown in Fig. 57-6 ~ Fig. 57-9









