全部
  • 全部
  • 产品管理
  • 新闻资讯
  • 介绍内容
  • 企业网点
  • 常见问题
  • 企业视频
  • 企业图册

Product Description

Swing check valve

 

1. Introduction

1.1. Purpose

Swing check valve is used to control the flow direction of medium in various pipeline systems of power plant.

1.2. Model meaning

H**##@@-&&$$/※※

H --- code of check valve

**-----Structure type code (see table 42-1)

##-------L stands for vertical: W stands for horizontal; L1 stands for vertical with taps: W1 stands for horizontal with taps

@@----------Valve seat sealing surface or lining material code

&&-------------Nominal pressure (MPA)

$$-------Material of valve body

※※--------Nominal diameter (mm)

Table 42-1 structure code of swing check valve

Structural type Code
Up and down Lift sraight through 1
Vertical 2
Swing Single petal 4
Multi petal 5
Double petal 6

Example: H4 WY-36C / 200 refers to check valve, with swing single valve structure, horizontal installation mode, cemented carbide sealing surface of valve seat, and nominal pressure of 36MPa, The material of the valve body is carbon steel, and the nominal diameter of the valve body is 200 mm. The nominal diameter is selected according to GB 1047-2005 (definition and selection of DN (nominal size) of pipeline components), and the nominal pressure is selected according to GB 1048-2005 "definition and selection of PN (nominal pressure) of pipeline components".

1.3. Structural features (see figure 42-1)

The disc of swing check valve is rocker plate. When the flow direction of medium is normal, when the inlet pressure is higher than the outlet pressure, the valve disc opens and the medium flows through the valve; when the outlet pressure is lower than the inlet pressure, the valve disc closes. Due to the use of rotating plate type hoist, the liquid flow is smooth and the resistance coefficient is small. The sealing surface is overlaid with cemented carbide and grinded. It has good erosion resistance and sealing performance, is not easy to leak, and operates reliably. The higher the pressure, the better the sealing performance. According to different applications, vertical and horizontal layout can be adopted.

 

2. Main technical parameters and product appearance

2.1. See table 42-2 for main technical parameters

Table 42-2 main technical parameters of H series check valve

Item Parameter
Nominal pressure(MPa) 0~75(4500 Poung grade)
Nominal diameter (mm) 20~500
Applicable units 50~1000MW units
Rated flow (t/h) 0~3600
Working temperature(℃) ≤570
Working medium Water, steam
Connection form of inlet and outlet Flange connection or butt welding connection
Supporting actuator Electric, pneumatic or other

2.2. Product appearance (see figure 42-2)

 

3. Selection method

Generally, the selection of valves can refer to the recommended valve structure and type to determine the main technical conditions of the valve. According to the regulation requirements and the working temperature, pressure, density, noise and other conditions of the medium, not only the flow characteristics and flow coefficient should be considered For the inherent static characteristics of valves such as CV or KV, allowable pressure difference and regulation range R, the influence of the dynamic characteristics such as the distortion of flow characteristics caused by the changes of system resistance and operating conditions due to the different parallel and series positions of the valves installed on the actual pipeline must also be considered.

 

4. Scope of supply and general product specifications

4.1. Scope of supply

It includes the valve body and the actuator matched with the valve. Other accessories, such as interface pipe. The selection of reducing joint shall be based on the user's requirements.

4.2. General technical specifications

Valve product design reference standard:

ASTM A182 / A182M-2008     Forged or rolled alloy steel nominal pipe flanges, forged pipe fittings, valves and parts for high temperature service

ASME B16.34-2004    Flanged, threaded and welded valves

ASME B16.10-2000     Valve structure length

ASTM A370-2003a       Definite and test method for mechanical properties of steel products

ASTM A-388 / A 388M-2004       Standard Practice for ultrasonic inspection of heavy steel forgings

GB / T12224-2005       General requirements for steel valves

GB / T 10868-2005       Desuperheating and pressure reducing valve for power station

GB / T 13927-1992        General purpose valve pressure test

GB / T 5097-2005         Non destructive testing, penetrant testing and magnetic particle testing observation conditions

GB / T 19672-2005         Specification for pipeline valves