PRODUCTS CENTER
Zimbabwe Segmented gear/tooth drive
Category:
Product Description
1. Lubrication of gear drive
The friction and wear of gears in meshing transmission will cause power loss and reduce transmission efficiency. Therefore, it is very necessary to lubricate the gear transmission, especially the high-speed and heavy-duty gear transmission. Good lubrication can not only reduce the wear and noise of the gear transmission, but also ensure the heat dissipation and anti-corrosion.
1.1. Lubrication mode of gear transmission
The lubrication mode of gear transmission is mainly determined by the circumferential speed of gear and the requirements of specific working conditions. In the closed gear transmission, when the circumferential speed of the gear is less than 10m / s, the big gear is usually lubricated with oil. The lubrication principle is that the big gear brings the oil into the meshing tooth surface for lubrication when the gear is running, and at the same time, the oil is thrown onto the box wall to dissipate heat; When v ≥ 10m / s, oil injection lubrication is usually used, that is, oil is sprayed to the meshing surface of gear teeth with a certain pressure for lubrication and heat dissipation; For low speed gear transmission or open transmission, regular manual lubrication can be used.
1.2. Selection of gear lubricating oil
The selection of gear lubricating oil is determined by gear type, working condition, load, speed and temperature rise.
2. Maintenance of gear drive
2.1. When using gear transmission, try to be stable in the process of starting, loading, shifting and braking to avoid impact load; In order to prevent tooth breakage and other faults.
2.2. Regularly check the condition of the lubricating system, such as the quantity of lubricating oil, oil supply condition, lubricating oil quality, etc., and regularly replace or supplement the specified brand of lubricating oil according to the use rules.
2.3. Pay attention to monitor the working condition of the gear transmission, if there is any abnormal sound or overheating of the box. It is easy to cause gear failure due to poor lubrication and unqualified assembly. Therefore, sound monitoring and regular inspection are also important methods to detect gear damage while ensuring the correct installation process.
3. Gear repair
In production, the common gear damage mainly includes overheat wear, pitting, tear marks and broken teeth. It should be repaired or changed according to different situations. The following describes several common repair methods.
3.1. Surfacing method
Some teeth or whole ring teeth can be overlaid to repair some damaged teeth or restore worn tooth profile. The specific operation steps are as follows:
3.1.1. Remove the damaged teeth and clean them up;
3.1.2. Build up welding for tooth repair;
3.1.3. Cutting teeth (such as milling teeth);
3.1.4. Necessary heat treatment.
For example, for carburized gears of 15Cr and 20Cr, 20Cr and 40Cr steel wires can be used for surfacing with reducing flame or neutral flame (gas welding); The valve spring steel wire (65Mn) can also be used for manual electric welding surfacing, but the steel wire should be coated with welding flux at this time. After the surfacing inspection is qualified, the outer circle and end face shall be machined on the lathe, the teeth shall be milled on the milling machine, and then carburized and tempered.
3.2. Inlay method
This method is generally used when the teeth of the gear are large. The specific operation method is to use the machine tool to cut off the bad tooth and install a new tooth. If it is a single tooth, the root part of the tooth is often made into a dovetail shape and inlaid with the gear body; If there are several teeth, they can be connected together to form a dovetail body, and then fixed or welded with countersunk screws.
3.3. Displacement cutting method
Generally, the modification machining method can be used for the larger gear after wear. That is to say, scrap the pinion, process the worn part of the large gear with negative modification, and then replace the pinion with a positive modification.
In addition, if the gear is one-way transmission, the direction can be changed after working for a period of time, that is, turning 180 ° use.
It should be noted that: ① the gear damage sometimes results from incorrect installation and use, so the correct installation should be ensured; ② The repaired gears should be inspected for backlash and contact spots, and can only be used after meeting the requirements; ③ Generally, the repaired gears should be run in first and then used; ④ The gears which are seriously damaged, difficult to repair or uneconomical to repair shall be replaced.