PRODUCTS CENTER
Product Description
ZJ series ring coal feeder
1. Introduction
Ring type coal feeder is a kind of equipment which adopts cylinder storage, mixing and distributing bulk materials. It is a device for power plants and coking plants to distribute various fuels reasonably and quantitatively according to different coal blending requirements, especially for power plants according to different electric and thermal load conditions and the most economic principle of fuel consumption increasing slightly. The device consists of a coal unloading car, a coal plough car and auxiliary devices.
1.1. Purpose
The ring coal feeder is the supporting equipment of the annular gap discharging cylinder silo. When the silo is used together with the equipment, it can realize the functions of coal storage and coal blending in coal-fired power plant. The equipment adopts frequency conversion speed regulation system, which can realize stepless speed change and realize the function of proportioning coal according to the change of coal type. It can unload the coal stored in the silo evenly to the coal conveying belt according to the required quantity and proportion, which can not only save the site, but also carry out coal blending and reduce the pollution of coal dust to the environment.
1.2. Model meaning
ZJ**##/$$
ZJ -- ring coal feeder for silo
**-- driving form (x is pin tooth drive, C rack drive)
##---- maximum productivity (T / h)
$$--- inner diameter of cylinder silo (m)
1.3. Structural features and working principle
The ring type coal feeder is composed of plough car, coal unloading car, driving unit, positioning guide device, plough coal unloader, walking track, sealing device, electrical control system, etc,
The plough car and coal unloading car are driven by three sets of pin teeth or rack transmission units, and the burning center makes circular movement. This drive can be used in the working place with much dust and poor lubrication condition, and it is convenient to disassemble and repair. The circular running direction of coal plough car and coal unloading car is opposite. After the coal plough car is started, the coal plough claw ploughs the coal in the annular gap coal groove to the coal bearing plate of the coal unloading car in operation. The coal unloading car drives the coal seam to rotate, and is pushed to the coal hopper beside the coal unloading vehicle by the plough type unloader, and then output by the belt conveyor below. The output of the equipment can be adjusted by adjusting the angle of coal plough claw or the frequency of frequency converter.
The positioning and guiding device is arranged 15 ° left and right with the driving device as the axis in the circumferential direction to protect the driving unit from impact.
The sealing device adopts rubber contact seal, which can adjust and replace rubber plate easily.
There are three kinds of electrical control modes: debugging, local control and centralized control. The coal plough car and coal unloading car can adopt frequency conversion speed regulation, so as to realize the needs of different output and coal blending during coal unloading. The equipment is equipped with corresponding protection and interlock devices, which are interlocked with conveyor belt conveyor and silo coal level meter. At the same time, the centralized control interface is reserved to facilitate the white automation operation of the whole coal handling system.
1.4. Product series
The product has ZJ700 / 15, ZJ000 / 15, ZJ700 / 22, ZJ200 / 22 and ZJ200 / 36.
2. Main technical parameters
The main technical parameters of ZJ series ring coal feeder are shown in table 41-1
| Model | ZJ700/15 | ZJ1000/15 | ZJ700/22 | ZJ1200/22 | ZJ1200/36 |
| Capacity(t/h) | 400~700 | 400~1000 | 400~1000 | 400~1200 | 6400~1200 |
| Particle size(mm) | ≤300 | ≤300 | ≤300 | ≤300 | ≤300 |
| Moisture content (%) | ≤12 | ≤12 | ≤12 | ≤12 | ≤12 |
3. Equipment appearance and structural dimensions
See Fig. 41-1 for the outline and structural dimensions of ZJ series ring coal feeder
4. Selection method
The equipment can be used not only as coal blending equipment, but also as coal storage equipment, so as to increase the reliability of coal loading in power plant, with the characteristics of reducing land occupation and environmental protection. It has high use value in power plant. Technical agreement shall be signed by the user, design institute and manufacturer.
