PRODUCTS CENTER
Malta Dust suppression device
Category:
Product Description
1. Brief introduction of dry fog dust suppression system
The basic principle of dry fog dust suppression is to produce granular water and mist like water of different sizes and shapes by the machine, and then adsorb and hold the particles of different strength and shapes with the air. After that, it will automatically combine and fall directly on the conveyor belt of the conveyor due to the action of gravity, so as to complete the operation mechanism.
1.1. Composition of dry fog dust suppression device
The dry fog and dust suppression devices are mainly composed of dry mist and dust suppression machine, screw air compressor, sprayer and water gas connecting pipe, heat tracing system, automatic control system and so on.
1. 2. Main characteristics of dry fog dust suppression
Dry fog dust suppression is mainly characterized by dust treatment at the dust point of the pollution source, and it can effectively suppress the dust, with high efficiency, no pollution, no need to clean the dust. The treatment effect of inhalable dust is very good, and it can avoid the harm of silicosis. In addition, the particles belong to the dry fog level, which will form a fog pool near the dense dust suppression point. And it through automatic control, occupies a small area, greatly reduces the investment, and the reliability and safety of the system is high, maintenance and operation costs are low. It is more suitable for unorganized emission, reducing the possibility of dust explosion, so that the investment of fire equipment is reduced, and it can be used normally in winter, which can greatly reduce the operation cost.
2. Technical requirements of dry fog dust suppression system
2.1. Controller of dry fog dust suppression system
The dry fog control system has the alarm indication of spray display, spray stop, low air pressure, low water pressure and water filter blockage. It has automatic and manual operation mode and can be operated on the touch panel of the dry fog control panel. The redundancy of the terminals, relays, contactors and circuit breakers of the controller is more than 30%. Each solenoid valve of dry fog box shall be set with independent grounding protection, which can automatically trip when the solenoid valve or corresponding line is grounded. The protection grade of all solenoid valves is IP67. It is required that all solenoid valve junction boxes can be easily removed during maintenance.
2.2. Pipeline of dry fog dust suppression system
All pipes and fittings are made of hot-dip galvanized steel pipe, and the thickness of pipe wall is not less than 4mm. Change the position of the spray box bracket, so that the spray box extends to the direction of the car dumper for about 10 centimeters, and is located under the water pipe and the airway Road, and the spray angle can be adjusted. The hose pipe connected to the spray box can meet the pressure of the system, and the length is suitable, both ends are convenient to disassemble and assemble, and are convenient for maintenance. The filter element installed in the main pipe is a reusable fine filter, which can remove 200μm particles in the media.
2.3. Dry fog dust suppression system
All valves, hoses and other devices need to be disassembled. When installing, make sure there is a flexible joint at one end to facilitate disassembly. All modification parts shall not affect the dust suppression effect on site, and the standard shall not be lower than the original design. Before acceptance, the whole dry fog dust suppression system should be debugged and inspected, and the parts that may cause faults should be dealt with in time. During the warranty period, the whole system shall operate normally, and there shall be no water leakage or air leakage in pipe joints, nozzles and other parts, or other device damage caused by design, type selection and construction.
2.4. The spray box receives the gas and water transported by the dry mist machine and transforms it into water droplets with a diameter of 1~10 μm. According to the control command of the dry fogger, spray to the dust suppression area. The dry fog and dust particles contact and collide with each other, which makes the dust particles cohere and agglomerate with each other, and settle under their own gravity, so as to achieve the effect of dust suppression.
3. Dust suppression technical scheme
The main function of the spray box is to receive the water vapor and water transported by the dry fog machine and transform them into a small size dry fog. The system can be transported to the dust suppression area through the control system of the dry mist machine, so that the dry fog and dust interact with each other and collide, so that the dust particles are bonded together and become larger and larger, so that they can settle down under the gravity of their own. So as to achieve the effect of dust suppression.
3.1. Specific design of dust suppression system
Outside the platform railings in front of the car dumper, 7 sets of CWL-5 atomizer assembly boxes are installed along the full length of the car dumper, and 7 distribution boxes are installed to allocate water and air pressure. The installation height and angle of the atomizer depend on the site conditions. Six sets of CWL-5 atomizer assembly boxes are installed along the full length of the car dumper at the rear side of the car dumper. Six distribution boxes are installed to allocate water and air pressure. The installation height of the atomizer is flush with the platform surface; Two sets of CWL-3 atomizer assembly boxes are installed at both ends of the front side of the car dumper, and two distribution boxes are installed to allocate water and air pressure. The installation height of the atomizer is flush with the platform surface; Two sets of CWL-2 atomizer assembly boxes are installed at both ends of the rear side of the car dumper, two distribution boxes are installed to allocate water and air pressure, and the installation height of the atomizer is flush with the platform surface. The ultrasonic atomizer of the dust suppression system adopts interval automatic spraying mode. When the dump truck is about to start dumping coal, the ultrasonic atomizer set on the front side of the dumper, the rear side and the two ends start to spray. The tipper completes the turning and unloading, and then stops the spray when the reset is started. The spray operation instruction is given by the PLC operating system of the car dumper center control room.
3.2. Configuration of compressed air
3.2.1. Compressed air volume of air compressor. Two air-cooled screw air compressors with air pressure of 7kg / cm2 and air volume of 9.0m3/min are selected, and the motor power is 110KW.
3.2.2. Air tank. In order to prevent the fluctuation of air pressure during the operation of the equipment from affecting the atomization effect of the atomizer, the air compressor is equipped with an air tank. The volume of the air storage tank accounts for one third of the air pressure of the air compressor, and the pressure is 8 kg /cm2.
3.2.3. Compressed air pipe network. DN61 stainless steel pipe with a wall thickness of 3.5 mm is used as the main pressure gas pipe. DN50 stainless steel pipe with a wall thickness of 3.5 mm is used as the main pressure gas pipe of the ring bin. DN20 stainless steel pipe with a wall thickness of 2.5 mm is used as the pressure gas branch pipe before entering the distribution box.
3.2.4. Water allocation
The water required by the ultrasonic atomizer is from the clean water in the plant area. In addition, an automatic water cleaning and filtering device is set on the main water inlet pipe, and the automatic cleaning cycle is set according to the water quality. After calculation, the amount of dust removal water is 2.4m3/h. The main water pipe adopts DN25 stainless steel pipe with a wall thickness of 2.5mm, and the water branch pipe before entering the distribution box adopts DN 15 stainless steel pipe with a wall thickness of 2.5mm. In order to prevent the water pipe from freezing in winter, the water pipe adopts electric tracing, and the outer wall of the water pipe is wrapped with polyurethane insulation cotton, which is protected by 0.5mm thick galvanized or stainless steel plate.
3.3. Electrical control of dust suppression system
The normal control of dust suppression electrical control system equipment is automatically operated by external contact signal through PLC. The machine side operation box is set, and the automatic and manual options are set on the machine side operation box. When the manual mode is selected, it is controlled by the start and stop buttons on the local operation box. The mode is single machine single action mode, which is used in the debugging stage; When automatic is selected, it works when the external start signal is sent out, and stops when the external stop signal is sent out .
4. Conclusion:
In conclusion, after the implementation of ultrasonic atomization dust suppression, the dust removal efficiency is more than 95%, and the dust pollution can be significantly improved. The water consumption of the dust suppression system is less than 2.4m3/h, and the humidification of coal after dust removal is less than 0.12%, which will not affect the transportation and reduce the thermal efficiency of coal combustion. The dust removal energy consumption of the system is less than 114kwh, which is lower than other types of dust removal equipment. The spray dust removal system adopts PLC operating system automatic control, spray starting and dump truck operation, and no need to increase operator, low operation cost and high working efficiency.