PRODUCTS CENTER
Malta GSQ series booster pump
Category:
Product Description
GSQ series booster pump
1. Introduction
1.1. Application
GSQ series booster pumps are mainly used for boiler feed water pumps of 300 MW and 600 MW thermal power units, and can also meet the selection and matching of units with different capacities.
1.2. Model meaning
**-GSQ##-&&
**---Nominal size of inlet diameter (mm)
GSQ -- boiler feed water booster pump
##-----------Flow rate (m3/s)
&&---------------head (m)
1.3. Structural features
1.3.1. Structural form. See Fig. 9-1 for horizontal split Horizontal single-stage double suction centrifugal pump

1.3.2. Structure description:
1.3.2.1. GSQ series booster pump is a horizontal split Horizontal single-stage double suction centrifugal pump, its suction and discharge outlet are under the pump axis line, perpendicular to the pump shaft in a horizontal direction; the pump case is double volute, with axial split, so it is unnecessary to remove the inlet and outlet pipelines and the driver during maintenance.
1.3.2.2. The pump shell is supported on the pump seat of steel welding structure. The joint surface of the pump shell and the pump seat is close to the center line of the pump shaft, and the key configuration can keep the longitudinal and transverse alignment, which can meet the requirements of thermal expansion, so as to ensure the stability and reliability of the pump operation.
1.3.2.3. The impeller is designed as a symmetrical double suction flow passage. The liquid enters the impeller from four sides, which can balance the axial force automatically and bear the residual axial force by the tapered roller bearing at the shaft end.
1.3.2.4. After static balance and dynamic balance verification, the impeller is fixed on the pump shaft by the key and impeller nuts on both sides of the impeller. The forward position can be adjusted by the nut to make the impeller locate on the center line of the volute chamber of the pump housing; the two ends of the pump shell corresponding to the impeller mouth ring are provided with sealing rings to reduce leakage, and can be replaced timely after wear.
1.3.2.5. The pump rotor, which is composed of pump shaft, impeller, impeller nut, bearing, bearing retainer sleeve and pump coupling, is supported on the bearing body at both ends of the pump shell. The transmission end of the rotor is provided with radial cylindrical roller bearing, and the free end is a pair of bidirectional symmetrical tapered roller bearings, which can bear the residual axial force
1.3.2.6. The shaft seals at both ends are single end face balanced mechanical seals with normal sealing performance and long service life. The seal body is equipped with water-cooled spacer sleeve, which can lower the temperature around the rotating part of the mechanical seal and prevent the liquid temperature from transferring to the bearing direction.
1.3.2.7. The pump is connected with the motor through diaphragm coupling. Diaphragm coupling is a flexible and torsional rigid transmission mechanism, which has the advantages of good compensation and power transmission capacity, and can absorb and isolate vibration, so it is safe and reliable to use.
2. Main technical parameters and product appearance
2.1. Main technical parameters
2.1.1. Typical technical parameters (see table 9-1)
Table 9-1 typical technical parameters of GSO series booster pump
| Item | Parameters |
| Inlet flow(m3/h) | 610~1240 |
| Head(m) | 147~94 |
| Temperature(℃) | ≤210 |
| Nominal diameter(mm) | 350~400 |
| Nominal pressure(MPa) | 2.5 |
2.1.2. Performance parameters (see table 9-2)
Table 9-2 performance parameters of GSQ series booster pump
| Modle | Flow | Head | Speed | Efficiency | NPSH(m) | Density | Shaft power | Unit load (MW) |
Meet unit capacity (%) |
| (m3/h) | (m) | (r/min) | (%) | (kg/m3) | (KW) | ||||
| 350GSQ610-102 | 610 | 102 | 1480 | 81.5 | 2.4 | 892.1 | 185.5 | 300 | 50 |
| 400GSQ1150-147 | 1150 | 147 | 1480 | 82 | 3 | 892.1 | 500.9 | 300 | 100 |
| 350GSQ648-100 | 648 | 100 | 1480 | 81 | 2.5 | 852.8 | 185.8 | 600 | 25 |
| 400GSQ1240-145 | 1240 | 145 | 1480 | 83 | 3.7 | 892.1 | 526.3 | 600 | 50 |
| 400GSQ1240-145 | 1240 | 145 | 1480 | 83 | 3.7 | 852.8 | 503.1 | 600 | 50 |
2.2. Product appearance (see Figure 9-2)

3. Scope of supply
Booster pump body, coupling, base, motor, anchor bolt.