PRODUCTS CENTER
Malta Prefilter (tubular filter)
Category:
Product Description
Prefilter (tubular filter)
1. Introduction
1.1 purpose
Polypropylene fiber foldable filter element is installed in the prefilter. According to the pore size of different filter elements, the impurities of solid particles with different particle sizes in water can be removed. The equipment is mainly used in condensate polishing system because of its large capacity. At present, more and more units with capacity of 600 MW and above have high quality requirements for water and steam quality during operation of these supercritical or ultra supercritical units. A pre filter is installed in front of the mixed bed unit to remove the impurity particles with iron oxide as the main component in the system. When the iron content is less than 2000 UG / L (the maximum can be 4000 UG / L), the prefilter can be put into operation in advance, and the iron removal efficiency can reach more than 80%.
1.2 model significance
GYL170
G --- filtration
Y ------ pressure type
L -------- filter element
170 --- equipment diameter mm
1.3 structural features
1.3.1. The bottom water inlet device is baffle water distribution device.
1.3.2. The bottom water outlet device is in the form of porous filter element.
1.3.3. All polypropylene fiber folded filter elements are fixed on the lower porous plate.
1.3.4. Epoxy resin anti-corrosion coating is used for internal surface of equipment.
1.3.5. The pressure grade of interface flange is pn3.5
1.4 product series
See table 45-1 for prefilter product series
Table 45-1 main product series of prefilter
| Nominal diameter | DN1600 | DN1700 | DN1800 | DN2000 |
| Model | GYL160 | GYL170 | GYL180 | GYL200 |
| filter elment flux(m3/h) | 3.5~4.5 | 3.5~4.5 | 3.5~4.5 | 3.5~4.5 |
| No. of filter element(PCS) | 180 | 225 | 300 | 400 |
| Desgin capacity(t/h) | 630 | 787 | 1050 | 1400 |
| Design weight(kg) | 6200 | 7424 | 7830 | 8858 |
| Running load(N) | 18000 | 19000 | 20000 | 21000 |
| Typical application(MW) | 300 | 300 | 600 | 1000 |
| 600 | 1000 |
2. Technical parameters
The main technical parameters of prefilter are shown in table 45-2
| Design pressure(MPa) | 3.5-5.0 | Filtration accuracy (um) | Foldable |
| Design temperature(℃) | 60 | Filter element form | Q235-B |
| Welded joint coefficient | 1 | Filter element flux (m3/h) | 3.5-4.5 |
| material of the main body | Q345R | container form | Vertical |
Note: the filter elements used are based on graver products.
3. Equipment appearance and structural dimensions
The configuration of prefilter is shown in Fig. 45-1 and table 45-3

| Nominal diamter Item |
DN1600 | DN1700 | DN1800 | DN2000 |
| H | 4650 | 4490 | 4920 | 4920 |
| h | 500 | 500 | 500 | 500 |
| ∮ | 1650 | 1760 | 1860 | 2060 |
| L1 | 500 | 500 | 500 | 580 |
| L2 | 500 | 500 | 500 | 600 |
| L3 | 500 | 500 | 500 | 600 |
| N1 | DN250 | DN300 | DN300 | DN400 |
| N2 | DN250 | DN300 | DN300 | DN400 |
| N3 | DN450 | DN500 | DN500 | DN500 |
| N4 | DN100 | DN100 | DN100 | DN100 |
| N5 | DN100 | DN100 | DN100 | DN100 |
| N6 | DN500 | DN500 | DN500 | DN500 |
| N7 | DN100 | DN100 | DN100 | DN100 |