PRODUCTS CENTER
Malta Quartz sand floating bed ion exchanger
Category:
Product Description
Quartz sand floating bed ion exchanger
1. Introduction
1.1. Purpose
The equipment is a pure water treatment equipment. When the salt content of raw water is less than 500 mg / L, the salt content can be reduced to less than 10 mg / L after passing through the positive floating bed and the negative floating bed; when the salt content of the raw water is more than 500 mg / L, the weak type and strong type resin can be used in series; when the salt content of raw water is higher, it can also be combined with other pre desalination methods such as reverse osmosis. If the effluent quality is higher, secondary desalination equipment can be set.
1.2. Model meaning
JFL100•200A
J -- Ion Exchange
FL --- floating bed, lining
100 -------- equipment diameter (mm)
200 -------- resin layer height (mm)
A -------- quartz sand mold
1.3. Structural features
The influent water is in the form of dome shaped porous plate and quartz sand.
1.3.2. The outlet water is in the form of porous plate.
1.3.3. The equipment is equipped with local sampling device and water inlet and outlet pressure gauges.
1.3.4 the pressure of all interface flanges of the equipment is PN1.0MPa.
1.3.5. The equipment can be equipped with manual rubber lined diaphragm valve or pneumatic rubber lined diaphragm valve.
1.3.6. The valve at resin loading and unloading port is DC rubber lined diaphragm valve or ball valve.
1.3.7. When the diameter DN ≤ 1250, the large flange structure is adopted at the porous plate.
1.3.8. The equipment is lined with 1751 semi-rigid adhesive for anti-corrosion.
1.4. Product series
See table 18-1 for the product series of quartz sand floating bed ion exchanger
Table 18-1 quartz sand floating bed ion exchanger product series.
| Nominal diameter resin layer height item |
DN1000 | DN1250 | DN1600 | DN1800 | ||||||||||||
| 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | |
| JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | |
| 100·200A | 100·250A | 100·280A | 100·320A | 125·200A | 125·250A | 125·280A | 125·320A | 160·200A | 160·250A | 160·280A | 160·320A | 180·200A | 180·250A | 180·280A | 180·320A | |
| design capacity (t/h) | 35 | 50 | 80 | 100 | ||||||||||||
| Resin volume (m3) | 1.57 | 1.96 | 2.2 | 2.51 | 2.45 | 3.07 | 3.44 | 3.93 | 4.02 | 5.03 | 5.63 | 6.43 | 5.1 | 6.36 | 7.12 | 8.14 |
| compressed resin volume (m3) | 0.157 | 0.245 | 0.4 | 0.51 | ||||||||||||
| Design mass (kg) | 1655 | 1725 | 1765 | 1825 | 2460 | 2540 | 2610 | 2695 | 3090 | 3209 | 3280 | 3698 | 4050 | 4229 | 4336 | 4889 |
| Operating load (N) | 61000 | 66000 | 70000 | 74000 | 95000 | 103000 | 108000 | 114000 | 141000 | 154000 | 162000 | 173000 | 193000 | 203000 | 223000 | 243000 |
| Nominal diameter resin layer height item |
DN2000 | DN2200 | DN2500 | DN2800 | ||||||||||||
| 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | |
| JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | |
| 200·200A | 200·250A | 200·280A | 200·320A | 220·200A | 220·250A | 220·280A | 220·320A | 250·200A | 250·250A | 250·280A | 250·320A | 280·200A | 280·250A | 280·280A | 280·320A | |
| design capacity (t/h) | 125 | 150 | 195 | 245 | ||||||||||||
| Resin volume (m3) | 6.28 | 7.85 | 8.79 | 10.05 | 7.6 | 9.5 | 10.64 | 12.16 | 9.8 | 12.25 | 13.72 | 15.7 | 12.31 | 15.39 | 17.24 | 19.7 |
| compressed resin volume (m3) | 0.63 | 0.76 | 0.98 | 1.23 | ||||||||||||
| Design mass (kg) | 4510 | 4695 | 4814 | 4973 | 5840 | 6113 | 6277 | 6495 | 6865 | 7175 | 7361 | 7609 | 8320 | 9165 | 9500 | 9830 |
| Operating load (N) | 193000 | 271000 | 289400 | 313500 | 263000 | 286000 | 304000 | 321000 | 392000 | 432000 | 443000 | 449000 | 325000 | 447000 | 478000 | 482000 |
2. Technical parameters
2.1. Main technical parameters
The main technical parameters of ion exchange in quartz sand floating bed are shown in table 18-2
Table 18-2 main technical parameters of quartz sand floating bed ion exchanger
| Item | Data | Item | Data |
| Design pressure(MPa) | 0.6 | container form | Vertical |
| Design temperature(℃) | 50 | Welded joint coefficient | 0.85 |
| design flow rate(m/h) | 40 | material of the main body | Q235-B |
| Design capacity(t/h) | see table 18-1 | Resin layer height(mm) | see table 18-1 |
2.2. Special parameters
The turbidity of influent water should be less than 2mg / L
3. Equipment appearance and structural dimensions
The external and structural dimensions of quartz sand floating bed ion exchanger are shown in Fig. 18-1, table 18-3 and table 18-4

Table 18-3
| Nominal diameter Resin layer height Item |
DN1000 | DN1250 | DN1600 | DN1800 | DN2000 | DN2200 | DN2500 | DN2800 | |||||||||||||||||||||||||
| 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | 2000 | 2500 | 2800 | 3200 | ||
| H | 4717 | 5217 | 5517 | 5917 | 4901 | 5401 | 5701 | 6101 | 5284 | 5784 | 6084 | 6484 | 5170 | 5670 | 5970 | 6370 | 5220 | 5720 | 6020 | 6420 | 5307 | 5807 | 6107 | 6507 | 5484 | 5984 | 6284 | 6684 | 5661 | 6161 | 6461 | 6861 | |
| H1 | 4217 | 4717 | 5017 | 5417 | 4401 | 4901 | 5201 | 5601 | 4784 | 5284 | 5584 | 5984 | 4670 | 5170 | 5470 | 5870 | 4720 | 5220 | 5520 | 5920 | 4807 | 5307 | 5607 | 6007 | 4984 | 5484 | 5784 | 6184 | 5161 | 5661 | 5961 | 6361 | |
| H2 | 3500 | 4000 | 4300 | 4700 | 3600 | 4100 | 4400 | 4800 | 3600 | 4100 | 4400 | 4800 | 3700 | 4200 | 4500 | 4900 | 3740 | 4200 | 4500 | 4900 | 3700 | 4200 | 4500 | 4900 | 3800 | 4300 | 4600 | 5000 | 3900 | 4400 | 4700 | 5100 | |
| H3 | 1200 | 1300 | 1300 | 1400 | 1400 | 1400 | 1500 | 1600 | |||||||||||||||||||||||||
| H4 | 300 | 400 | 400 | 400 | 400 | 400 | 500 | 500 | |||||||||||||||||||||||||
| H5 | 445 | 560 | 580 | 595 | 595 | 640 | 730 | 730 | |||||||||||||||||||||||||
| H6 | 1000 | 1000 | 1000 | 1200 | 1200 | 1200 | 1300 | 1300 | |||||||||||||||||||||||||
| H7 | 1450 | 1450 | 1450 | 1750 | 1750 | 1750 | 1850 | 1850 | |||||||||||||||||||||||||
| N×M | 100×140 | 180×220 | 180×220 | 180×220 | 180×220 | 180×220 | 300×350 | 300×350 | |||||||||||||||||||||||||
| L1 | 754 | 896 | 1091 | 1208 | 1308 | 1445 | 1595 | 1747 | |||||||||||||||||||||||||
| L2 | 145 | 160 | 180 | 195 | 195 | 230 | 230 | 230 | |||||||||||||||||||||||||
| L3 | 248 | 313 | 333 | 398 | 398 | 433 | 433 | 433 | |||||||||||||||||||||||||
| L4 | 180 | 200 | 210 | 230 | 230 | 280 | 280 | 280 | |||||||||||||||||||||||||
| LA~LD | See table 18-4 | ||||||||||||||||||||||||||||||||
| ∮ | 985 | 1000 | 1450 | 1600 | 1800 | 1900 | 2000 | 2150 | |||||||||||||||||||||||||
| DN1 | 80 | 80 | 100 | 100 | 100 | 100 | 100 | 100 | |||||||||||||||||||||||||
| DN2 | 32 | 40 | 50 | 50 | 50 | 80 | 80 | 80 | |||||||||||||||||||||||||
| DN3 | 50 | 80 | 100 | 125 | 125 | 150 | 150 | 150 | |||||||||||||||||||||||||
| DN4 | 80 | 100 | 125 | 150 | 150 | 200 | 200 | 200 | |||||||||||||||||||||||||
| DN5 | 32 | 50 | 80 | 80 | 100 | 125 | 125 | 125 | |||||||||||||||||||||||||
| DN6 | 32 | 40 | 40 | 40 | 40 | 40 | 50 | 50 | |||||||||||||||||||||||||
| quartz sand cushion | Particle size 1~2 | 200 | 200 | 200 | 200 | ||||||||||||||||||||||||||||
| Particle size 2~4 | 100 | 150 | 150 | 150 | |||||||||||||||||||||||||||||
| Particle size 4~8 | 100 | 100 | 100 | 100 | |||||||||||||||||||||||||||||
| Particle size 8~16 | 100 | 150 | 150 | 150 | |||||||||||||||||||||||||||||
| Particle size 16~32 | 250 | 250 | 250 | 300 | |||||||||||||||||||||||||||||
Table 18-4 LA ~ LD dimensions of quartz sand floating bed ion exchanger
| Main parameter Manual or Pneumatic type Sanders pneumatic Nominal diameter |
LA | LB | LC | LD |
| DN1000 | 160 | 160 | 210 | 300 |
| 150 | 150 | 194 | 258 | |
| DN1250 | 180 | 210 | 300 | 350 |
| 163 | 194 | 258 | 309 | |
| DN1600 | 210 | 300 | 350 | 400 |
| 194 | 258 | 309 | 362 | |
| DN1800 | 210 | 300 | 400 | 460 |
| 194 | 258 | 362 | 412 | |
| DN2000 | 210 | 350 | 400 | 460 |
| 194 | 309 | 362 | 412 | |
| DN2200 | 300 | 400 | 460 | 570 |
| 258 | 362 | 412 | 529 | |
| DN2500 | 300 | 400 | 460 | 570 |
| 258 | 362 | 412 | 529 | |
| DN2800 | 300 | 400 | 460 | 570 |
| 258 | 362 | 412 | 529 |
Note: for manual rubber lined diaphragm valve, LC and LD values are zero.
4. Ordering instructions
The regeneration liquid of the equipment is hydrochloric acid, sulfuric acid and sodium hydroxide.