PRODUCTS CENTER
Malta Porous plate & water cap type counter current regeneration ion exchanger
Category:
Product Description
Porous plate and water cap counter current regeneration ion exchanger
1. Introduction
1.1. Purpose
The equipment is used for water purification. During operation and regeneration, the direction of liquid flow through the exchanger is opposite. The regeneration degree is high, the consumption of regenerant is low, and the quality of effluent is guaranteed. However, the equipment and the regeneration operation are complicated, including three types of gas top pressure, water top pressure and no top pressure.
1.2. Model meaning
J NL 100•125 B
J-----------Ion exchange
NL -------- counter current regeneration and lining
100 -------- equipment diameter (mm)
125 -------- resin layer height (mm)
B -------- porous plate, water cap type
1.3. Structural features
1.3.1. The water inlet device is dome shaped porous plate
1.3.2. The regeneration liquid device in the middle is in the form of mother pipe and branch pipe.
1.3.3. The water outlet device is in the form of porous plate and water cap.
1.3.4. The equipment is equipped with local sampling device and water inlet and outlet pressure gauges.
1.3.5. The pressure rating of all interface flanges is PN1.0MPa.
1.3.6. The equipment can be equipped with manual rubber lined diaphragm valve and pneumatic rubber lined diaphragm valve.
1.3.7. The equipment is lined with 1751 semi-rigid adhesive for anti-corrosion.
1.3.8 when the equipment diameter DN ≤ 1250, the large flange structure is adopted at the porous plate.
1.4. Product series
See table 17-1 for the products of porous plate and water cap counter current regeneration ion exchanger
Table 17-1 product series of parallel flow regeneration ion exchanger with porous plate and water cap
| Nominal diameter resin layer height item |
DN1000 | DN1250 | DN1600 | DN1800 | DN2000 | ||||||||||
| 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | |
| JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | |
| 100·160B | 100·200B | 100·250B | 125·160B | 125·200B | 125·250B | 160·160B | 160·200B | 160·250B | 180·160B | 180·200B | 180·250B | 200·125B | 200·200B | 200·250B | |
| design capacity (t/h) | 15 | 25 | 40 | 50 | 65 | ||||||||||
| Resin volume (m3) | 1.26 | 1.57 | 1.96 | 1.96 | 2.45 | 3.07 | 3.2 | 4.02 | 5.02 | 4.07 | 5.1 | 6.36 | 5.02 | 6.28 | 7.85 |
| compressed resin volume (m3) | 0.16 | 0.25 | 0.4 | 0.51 | 0.63 | ||||||||||
| Design mass (kg) | 1691 | 1796 | 1936 | 2340 | 2489 | 2686 | 2870 | 3063 | 3322 | 3794 | 4073 | 4442 | 4268 | 4576 | 4982 |
| Operating load (N) | 45200 | 51620 | 57820 | 68630 | 78470 | 90810 | 111450 | 127090 | 146790 | 137120 | 157190 | 182500 | 169640 | 196030 | 226790 |
| Nominal diameter resin layer height item |
DN2200 | DN2500 | DN2800 | DN3000 | DN3200 | ||||||||||
| 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | |
| JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | JNL | |
| 220·125B | 220·200B | 220·250B | 250·160B | 250·200B | 250·250B | 280·160B | 280·200B | 280·250B | 300·160B | 300·200B | 300·250B | 320·160B | 300·200B | 300·250B | |
| design capacity (t/h) | 75 | 100 | 125 | 140 | 160 | ||||||||||
| Resin volume (m3) | 6.08 | 7.6 | 9.5 | 7.85 | 9.82 | 12.27 | 9.85 | 12.31 | 15.39 | 11.3 | 14.13 | 17.66 | 12.86 | 16.08 | 20.1 |
| compressed resin volume (m3) | 0.76 | 0.98 | 1.23 | 1.41 | 1.61 | ||||||||||
| Design mass (kg) | 5393 | 5807 | 6345 | 7100 | 7570 | 8182 | 8771 | 9391 | 10191 | 10025 | 10699 | 11574 | 10841 | 11557 | 12485 |
| Operating load (N) | 242680 | 274660 | 312330 | 273600 | 311700 | 359460 | 348180 | 395920 | 456620 | 404150 | 458890 | 527720 | 459440 | 521240 | 598830 |
2. Technical parameters
2.1. Main technical parameters
The main technical parameters of porous plate and water cap counter current regeneration ion exchanger are shown in table 17-2
Table 17-2 main technical parameters of porous plate and water cap counter current regeneration ion exchanger
| Item | Data | Item | Data |
| Design pressure(MPa) | 0.6 | container form | Vertical |
| Design temperature(℃) | 50 | Welded joint coefficient | 0.85 |
| design flow rate(m/h) | 20 | material of the main body | Q235-B |
| Design capacity(t/h) | see table 17-1 | Resin layer height(mm) | see table 17-1 |
2.2. Special parameters
The turbidity of influent water should be less than 2mg / L
3. Equipment appearance and structural dimensions
See Fig. 17-1, table 17-3 and table 17-4 for the outline and structural dimensions of multi hole type and water cap type forward flow ion exchanger

Table 17-3
| Nominal diameter Resin layer height Item |
DN1000 | DN1250 | DN1600 | DN1800 | DN2000 | DN2200 | DN2500 | DN2800 | DN3000 | DN3200 | ||||||||||||||||||||
| 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | 1600 | 2000 | 2500 | |
| H | 4456 | 5136 | 5986 | 4696 | 5376 | 6226 | 5167 | 5847 | 6697 | 5025 | 5705 | 6697 | 5025 | 5705 | 6555 | 5244 | 5924 | 6774 | 5496 | 6176 | 7026 | 5650 | 6330 | 7180 | 5787 | 6467 | 7317 | 5887 | 6567 | 7417 |
| H0 | 1800 | 1800 | 1800 | 1800 | 1800 | 1800 | 1800 | 1800 | 1800 | 1800 | ||||||||||||||||||||
| H1 | 129 | 229 | 214 | 194 | 194 | 194 | 229 | 229 | 194 | 194 | ||||||||||||||||||||
| H2 | 422 | 522 | 537 | 557 | 557 | 557 | 622 | 622 | 657 | 657 | ||||||||||||||||||||
| H3 | 715 | 915 | 860 | 920 | 920 | 920 | 1015 | 1015 | 1120 | 1120 | ||||||||||||||||||||
| H4 | 1450 | 1450 | 1450 | 1450 | 1450 | 1450 | 1600 | 1600 | 1600 | 1600 | ||||||||||||||||||||
| ∮ | 985 | 1000 | 1450 | 1600 | 1800 | 1900 | 2000 | 2150 | 2275 | 2400 | ||||||||||||||||||||
| L1 | 145 | 145 | 160 | 180 | 180 | 180 | 195 | 195 | 230 | 230 | ||||||||||||||||||||
| L2 | 248 | 248 | 313 | 333 | 333 | 333 | 398 | 398 | 433 | 433 | ||||||||||||||||||||
| L3 | 240 | 240 | 290 | 290 | 290 | 320 | 320 | 360 | 360 | 360 | ||||||||||||||||||||
| L4 | 729 | 856 | 1056 | 1158 | 1258 | 1375 | 1525 | 1697 | 1797 | 1897 | ||||||||||||||||||||
| L5 | 754 | 881 | 1071 | 1193 | 1293 | 1395 | 1560 | 1712 | 1847 | 1947 | ||||||||||||||||||||
| L6 | 180 | 180 | 200 | 220 | 220 | 220 | 280 | 280 | 280 | 280 | ||||||||||||||||||||
| L7 | 623 | 757 | 933 | 1033 | 1136 | 1240 | 1380 | 1536 | 1638 | 1740 | ||||||||||||||||||||
| LA~LE | see table 17-4 | |||||||||||||||||||||||||||||
| N×M | 100×14 | 180×220 | 180×220 | 180×220 | 180×220 | 180×220 | 300×350 | 300×350 | 300×350 | 300×350 | ||||||||||||||||||||
| DN1 | 80 | 80 | 100 | 125 | 125 | 125 | 150 | 150 | 200 | 200 | ||||||||||||||||||||
| DN2 | 50 | 50 | 80 | 80 | 80 | 100 | 100 | 125 | 125 | 125 | ||||||||||||||||||||
| DN3 | 32 | 32 | 40 | 40 | 40 | 40 | 40 | 50 | 50 | 50 | ||||||||||||||||||||
| ∮ | 985 | 1000 | 1450 | 1600 | 1800 | 1900 | 2000 | 2150 | 2275 | 2400 | ||||||||||||||||||||
Table 17-4 dimensions of LA ~ LD for parallel flow regeneration ion exchanger with porous plate and water cap
| Main parameter Manual or Pneumatic type Sanders pneumatic Nominal diameter |
LA | LB | LC | LD |
| DN1000 | 300 | 210 | 150 | 250 |
| 258 | 194 | |||
| DN1250 | 300 | 210 | 150 | 250 |
| 258 | 194 | |||
| DN1600 | 350 | 300 | — | 250 |
| 309 | 258 | |||
| DN1800 | 400 | 300 | — | 200 |
| 362 | 258 | |||
| DN2000 | 400 | 300 | — | 200 |
| 362 | 258 | |||
| DN2200 | 400 | 350 | 150 | 320 |
| 362 | 309 | |||
| DN2500 | 460 | 350 | — | 280 |
| 412 | 309 | |||
| DN2800 | 460 | 400 | — | 280 |
| 412 | 362 | |||
| DN3000 | 570 | 400 | 150 | 420 |
| 529 | 362 | |||
| DN3200 | 570 | 400 | 150 | 420 |
| 529 | 362 |
Note: for manual rubber lined diaphragm valve, LC, LD, LE values are zero.
4. Ordering instructions
The regeneration liquid of the equipment is hydrochloric acid, sulfuric acid and sodium hydroxide. When the flow rate of regeneration liquid is 10m / h, it should be indicated when ordering. If users use no top pressure regeneration, please indicate when ordering.