PRODUCTS CENTER
Product Description
GY Pressure filter
1. Introduction
1.1. Purpose
The pressure filter is used in the pretreatment equipment of ion exchange system. It uses the medium filtration to remove the suspended solids in the water and make the effluent clear. The equipment can be loaded with single layer or double layer filter material.
1.2. Model meaning
G-Y- 100•120
G ------ filtration
Y -------- pressure type (single or double layer)
100 -------- equipment diameter (cm)
120--------Height of filling layer (cm)
1.3. Structural features
1.3.1. The upper water inlet device is bell mouth type water distribution device.
1.3.2. The lower drainage device is in the form of perforated plate water cap.
1.3.3 when the equipment diameter is not less than 1600mm, the bottom manhole is on the side of the lower head.
1.3.4 black epoxy asphalt paint shall be used for anti-corrosion of internal surface of equipment.
The equipment is equipped with local sampling device and inlet and outlet pressure gauges.
1.3.6. The pressure rating of all interface flanges is PN1.0MPa.
1.4. Product series
See table 4-1 for the product series of pressure filter.
Table 4-1 product series of pressure filter
| Nominal Diameter Model Item |
DN1000 | DN1250 | DN1600 | DN2000 | DN2200 | DN2500 | DN3000 | DN3200 | |
| GY100·120 | GY125·120 | GY160·120 | GY200·120 | GY220·120 | GY250·120 | GY300·120 | GY320·120 | ||
| Designing flow rate | One layer | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 |
| (m/h) | Double layers | 12 | 12 | 12 | 12 | 12 | 12 | 12 | 12 |
| Designing capacity | One layer | 6.4 | 9.8 | 16 | 25 | 30 | 40 | 56 | 64 |
| (t/h) | Double layers | 9.5 | 14.7 | 24 | 38 | 46 | 59 | 84 | 96 |
| Designing weight(kg) | 1071 | 1505 | 2098 | 3249 | 3973 | 5296 | 7571 | 8216 | |
| Running load(N) | 39240 | 67290 | 108680 | 174780 | 214130 | 287820 | 419170 | 478210 | |
2. Technical parameters
2.1. Main technical parameters
The main technical parameters of pressure filter are shown in Table 4-2
Table 4-2 main technical parameters of pressure filter
| Item | Data | Item | Data |
| Design pressure(MPa) | 0.6 | Welded joint coefficient | 0.85 |
| Design temperature(℃) | 50 | material of the main body | Q235-B |
| Design flow rate(m/h) | See table 4-1 | design capacity(t/h) | See table 4-1 |
| Design height(mm) | See table 4-4 | container form | Vertical |
| Filtering type | See table 4-4 |
2.2. Special parameters
Turbidity: the influent water is 10-20mg / L, the effluent is 2-5mg / L; the influent is less than 10mg / L, and the effluent is less than 2mg / L.
2.3. Configuration and structural dimensions
See Figure 4-1, table 4-3 and table 4-4 for the outline and structural dimensions of pressure filtration equipment

Table 4-3 dimensions of pressure filter La ~ LD
| Nominal diameter Item |
DN1000 | DN1250 | DN1600 | DN200 | DN2200 | DN2500 | DN3000 | DN3200 |
| LA(Z44T-10) | 180 | 180 | 210 | 230 | 230 | 255 | 280 | 280 |
| LB(Z44T-10) | 210 | 210 | 255 | 280 | 280 | 330 | 380 | 380 |
| LC(Z44T-10) | 200 | 200 | 200 | 200 | 200 | 200 | 200 | 200 |
| LD(Z44T-10) | 230 | 230 | 230 | 310 | 310 | 350 | 350 | 350 |
Table 4-4 external dimensions of pressure filter
| Nominal Diameter Item |
DN1000 | DN1250 | DN1600 | DN200 | DN2200 | DN2500 | DN3000 | DN3200 |
| H | 3119 | 3251 | 3427 | 3665 | 3769 | 4021 | 4177 | 4377 |
| H1 | 270 | 270 | 205 | 170 | 170 | 195 | 210 | 210 |
| H2 | 800 | 800 | 800 | 800 | 800 | 800 | 827 | 827 |
| H3 | 880 | 950 | 1040 | 1150 | 1210 | 1380 | 1510 | 1560 |
| H4 | 1100 | 1100 | 1200 | 1200 | 1300 | 1300 | 1350 | 1350 |
| H5 | 995 | 1062 | 1151 | 1272 | 1324 | 1501 | 1580 | 1680 |
| ∮ | 985 | 1000 | 1450 | 1800 | 1900 | 2000 | 2275 | 2400 |
| L | 736 | 863 | 1103 | 1340 | 1442 | 1667 | 1924 | 2024 |
| L1 | 130 | 130 | 195 | 230 | 230 | 305 | 310 | 310 |
| L2 | 227 | 227 | 342 | 427 | 427 | 502 | 557 | 557 |
| L3 | 726 | 853 | 1028 | 1240 | 1342 | 1522 | 1774 | 1974 |
| L4 | 470 | 570 | 710 | 880 | 980 | 1105 | 1320 | 1420 |
| L5 | 479 | 606 | 716 | 883 | 985 | 1135 | 1307 | 1407 |
| L6 | 120 | 120 | 120 | 130 | 130 | 160 | 160 | 160 |
| LA~LD | Table 4-3 | |||||||
| N×M | 100×140 | 180×220 | 180×220 | 180×220 | 180×220 | 300×350 | 300×350 | 300×350 |
| DN1 | 50 | 50 | 80 | 100 | 100 | 125 | 150 | 150 |
| DN2 | 80 | 80 | 125 | 150 | 150 | 200 | 250 | 250 |
| DN3 | 50 | 50 | 50 | 80 | 80 | 100 | 100 | 100 |
| DN4 | 40 | 40 | 40 | 40 | 40 | 40 | 40 | 40 |
| Filter material gradation | ||||||||
| Single layer filter material | Quartz sand | particle size | 0.5~1.2 | layer height | 1200 | |||
| anthracite | particle size | 0.5~1.2 | layer height | 1200 | ||||
| Double layers filter material | Anthracite (upper layer) | particle size | 1.2~2.5 | layer height | 400 | |||
| Quartz sand (lower layer) | particle size | 0.5~1.2 | layer height | 800 | ||||